Panasonic TV Repair: Common Faults and Solutions.
Search: Panasonic
Results: 2880
Results: 2880
Panasonic Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PANASONIC | TC-L32E5BG | I changed the TV card, and the new one doesn't tune channels | Changing the main board, but not tuning channels | Rafael de Lira | |
| PANASONIC | TC-40DS600B | Burned LED panel (03 rulers with 08 LEDs each ruler and the LEDs are 6v) and each LED has 6.6 volts on top of it.... | Modification to reduce current (link on YouTube the nel 350: https://www.youtube.com/watch?v=fliqgp62tps) and then it deals with the tc-40d400 but the power supply is very similar to 40ds600b | Modify resistors r7837(1r), r7835(1r), r7826(1r), in my case I modified them to 2r7 and the voltage dropped from 42 volts to 38v. detail that the manμFacturers are dishonest and when you turn on the TV the voltage comes at 48 volts, then the pwm corrects it and drops to 38v, turn it on today, turn it on tomorrow and tsound it goes... in other words with this voltage above normal over time The LEDs will definitely go out... | MIGUELTV |
| PANASONIC | TC-L39EM6B TC-L39EM6B | Turns on with backlight without image | Usage time | Main board with pnl-12v line with low resistance - I looked until I found a smd c4002 capacitor with 24.6Ω | @Nelson.g24 |
| PANASONIC | SA-AK110 | Take out. CD tray opens and won't close. | CD mechanism out of time or reset by unloading the elco close to the processor on the front plate. | jr_TEC | |
| PANASONIC | SAAK110 | Take out. CD tray opens and won't close. | CD mechanism out of time or reset by unloading the elco close to the processor on the front plate. | jr_TEC | |
| PANASONIC | TC-L47DT50B | Does not turn on, inoperative | I replaced all the photo couplers in the power supply, it worked perfectly again | Eletrônica JJ | |
| PANASONIC | TC-32A400B | When turning on the power, the green LED flashes quickly for a few times and then the red LED starts flashing in a loop, once and pause, once and pause.... | So error 1, I put a LED kit on the outside without opening the TV and it resolved it, then the LED bus failed. | Replace panel/led kit | MIGUELTV |
| PANASONIC | TC-32ES600B TC-32FS600B | Pcf with around 300v, voltage on pin 3 of the pc7300 zero and some voltages present on the secondary but it does not turn on or stand by. | Check for a possible leak in d7307 (primary), it could be the glue or the component itself. | electronicssupplyparts - Gramado/RS | |
| PANASONIC | TC-L50E6B | TV turns on and backlight turns on, but no image +b and t-con 12v fuse ok | On the pci t-con it had lp1 with a defect in the solders and it did not generate 3v3 | YouTube Direto no defeito | |
| PANASONIC | TV 14C4 | Blowing fuse | Capacitors c813 (10uf 50v) and c812 (56uf 50v), both without liquid or exhausted. | After the replace everything was ok. | George Pontes |
| PANASONIC | TC-55AS700B LA51 | Does not turn on, backlight flashes and activates standby LED protection flashes red 1x | See possible problem with the rulers, each bank of LEDs lights up with 43v. If the LEDs are ok, check the power supply board. Tsound are 6 smd tr on the power supply board responsible for regulating the negative of the LED banks. One of them may have a short circuit, measure carefully as they are pnp transistors | Replace the shorted transistor 2sb1181 or replace the power supply lacquer if you can't find the transistor to buy | rafaelmoraes99 |
| PANASONIC | SA-AKX76 | Turns on, f16 appears on the display and then turns off. (false cooler error) | Voltage of 37v normal in c3300 but without audio and it was not the output. pin 40 of ic2006 could not go to zero if the cooler is spinning. | Transistor q2006(nb) was open, which led q2008 and q2010 to give negative voltage on pin 40 of the ic2006 processor. After exchanging the q2006 for a bc817 it started working again! | Ruizyn |
| PANASONIC | TC-L39EM6B | TV without image, backlight ok | 12v is missing on the v com board. Defective main board. | Main board ic5421 reg rt7257cl defective. | RNSPTEC |
| PANASONIC | SA-AK25 XXX | F61 | Introducing f61 | Capacitors showing leakage ESR 50v 2200μF, replace with 50v 3300 and the problem was resolved. Tsound are cases wsound it could be cold soldering on the fitting of the main plsca to the amplifier board, but in this case it was resolved due to the leakage of the wires. | Bruno trindade |
| PANASONIC | TC-L42E5BG | LED flashing 3 times | D7305 looks like a smd transistor | Replace d7305 on the power supply board | Jg eletronica |
| PANASONIC | TC-L42E5BG | Turns on, LED flashes 9 times | Ci audio bd5452a | Welber Luiz | |
| PANASONIC | TC32FS600B | Remote control doesn't work | Shorted smd capacitor on remote sensor board | Solution to replace it or remove it | nadobom |
| PANASONIC | TC-32A400B TNP4G572 | LED current very high | Remove two smd resistors, r7825 and r7824 | RODRIGO CELL | |
| PANASONIC | TC-L32X5B KM16 | TV does not turn on, without voltage on the power supply output connector, | Main board killing the 15.7v voltage, disconnecting the power connector, voltage appears, the cause is an unidentified smd capacitor that is next to pin 16 of connector a 09, which is shorted. obs. the credits for this post go to alex brynner from mg, who posted the defect on the "da jinni daelectronics" forum at | Replace the capacitor (0.1 μF) which can be removed from another condemned board. | Assolini BR |
| PANASONIC | TC 14RM15L | TV works, triggers protection and no longer turns on LED keeps flashing | Change ic880 | Like horror | Emerson Ribeiro |