SAMSUNG TV Repair: Common Faults and Solutions.
Search: SAMSUNG
Results: 3754
Results: 3754
SAMSUNG Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG | CB20S10BZ | Without image, with osd | R420 120k | ||
| SAMSUNG | CB-3335Z CHASSIS P69SA | Horizontal stripes across the screen. | Leaks on r305 and r308. | ||
| SAMSUNG | CB5020T CHASSIS SCT11D | White screen with vertical colored spots. | 220k r508 replacement on crt board | ||
| SAMSUNG | CX-5344N, CH S-51 | It takes a long time for the image to appear after turning on the device | Ic tda6108jf, on the kinescope board, with anomalies | ||
| SAMSUNG | CHASSIS P69SA | Does not come out of standby. | Eeprom 24c02 | ||
| SAMSUNG | CB 5035Z CHASSIS P69 | Gives sound. does not give an image. | The cathodes had little emission and the rgb was blocked. I got the kinescope back and everything was normal. | ||
| SAMSUNG | CB20B30BT -CHASSIS S15A | The LED turns on and off. the 8 v voltage on pin 8 of the ic802 does not appear. | Optocoupler pc801 | ||
| SAMSUNG | CB-5051X CH P68SC-N | It turns off with the remote control and turns on again but with an image sometimes with rain and no sound. | Replace q802 (2sc2331) which was leaking | ||
| SAMSUNG | CB-3351X | Image pulled 2 or 3 cm to the left, leaving a black bar on the right | C404 2n7 next to ic101 | ||
| SAMSUNG | CX-683 - CHASSIS S51 | Sometimes it doesn't start the horizontal | C407 - 1nf/2kv | ||
| SAMSUNG | SP47W3HF -RETROPROJECTOR | Deconverged image | Icz104 (stk392-040) no convergence module | ||
| SAMSUNG | CHASSIS S51A | Image with poor quality, the voltage of the g2 has a maximum value of 300v | Happened to crt thomson. the solution starts by replacing the transformer lines, 300v is very little, it should have a maximum value of 650v | ||
| SAMSUNG | CB-5073Z -CHASSIS SCT11B | White screen with thick horizontal white lines about 2cm apart that persist even when lowering the g2 | R508 (220k) no módulo do crt | ||
| SAMSUNG | CX-6230ZN | The power supply does not start | Substituir c808-100uf/25v | ||
| SAMSUNG | CX-6844N - CHASSIS S51A | There is no sound, but there is background noise like rain. | Go to service mode, menu option byte and select the pal b/g system indicated by the initials cb. After making this selection, exit the service menu, restart the TV, return to service mode and reset. et voilá, the sound appears after 5 seconds. | ||
| SAMSUNG | CB-504Z | The power relay turns on, but does not start, ypc is not powered | Trs: q403 (2sc2229) open, does not feed ypc. and the horizontal drive | ||
| SAMSUNG | CB-5073Z | The LED is always yellow and the TV doesn't turn on despite having the fa ok. | R914 47Ω 1/8w aberta. liga ao pino 16 do up "hold in" | ||
| SAMSUNG | CL21M21MQ | LED blinking and won't turn on | Diode 1n4148 in position j823 open. | ||
| SAMSUNG | CN-5039VB | Colored bars on the screen the same as the bar generator | Ci do vertical (tda8356-3y). | ||
| SAMSUNG | 540N | Turns on but the screen doesn't light up | C115 (1000uf/10v) exhausted |