SAMSUNG TV Repair: Common Faults and Solutions.
Search: SAMSUNG
Results: 3752
Results: 3752
SAMSUNG Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG | LN40D550 K1G | League without image, with back access. | Tcon. c4 with small leak. 1v2 low voltage. | Board had vgh and vgl. tcon panel v400h1. | joaomvjr |
| SAMSUNG | UN40C5000QM | Standby LED off, voltages ok, display ok and blacklight ok | Check the board with touch buttons, usually the SMD capacitor C03 shorts out and protects the power supply, preventing the TV from turning on | Location of the smd capacitor: close to the single electrolytic capacitor on the board, to confirm and just leave the TV plugged in and notice it heating up or with a thermal camera if you don't have it, touch it, you can feel the capacitor heating up. | Luiz |
| SAMSUNG | LN32B530 | Does not turn on a dead power supply, does not light up stb | Zener diode on the zm801 power supply board with small leaks. supply voltage of the ci strw on the cm808 capacitor keeps oscillating | Replace zm801 zener power supply board. | Play back |
| SAMSUNG | UN40C5000AG PSLF121B01A | The LED turns on and goes out quickly when plugged in, but it doesn't light up the screen or start the TV. | Use a 1k resistor between pins ps-on 18 and stby 16 to arm the power supply and carry out the tests. (use a filament lamp in series to avoid further damaging the circuit) | When you notice the absence of 5vdc or 12vdc: replace photo couplers pc 801s, pc 802s, pc 803s and pc 804s if the 12vdc still does not come back, replace zdm853 (ka or tl431) | Luiz |
| SAMSUNG | BE32 | Doesn't start | Smd capacitor near the LED connector next to the coil | CLEBER LIMA RS | |
| SAMSUNG | UN32EH5300 | Tv normal power supply main board without 5 volts std bay | Replace ic 201 e ic 202 | Eletrosideral Sapopemba | |
| SAMSUNG | LN32C530F1M | Does not turn on, secondary voltages pulsating | Cb802 at power supply | Replace | Hndrsn |
| SAMSUNG | LN32D403E2G | LED blinks, makes it turn on but doesn't turn on. | Capacitor 1113 on the main board near the memory (remove) | If I helped, if you can send a pix (79)98842-5366 | Luciano (Amplitec) |
| SAMSUNG | LE23R81B | Does not start | Stand-by LED active, but does not start | Rm814 - 3.3k 1w + dzm802 - bzx84c27 | RMELECTRONICA |
| SAMSUNG | UN40H6400AG | TV turns on but the backlight flashes or then goes out, the backlight does not remain on even if disconnected from the main PCI, in this model the normal thing is for the backlight to turn on as soon as the power supply is disconnected from the main | After excluding the possibility of a defect in the LED bus, check the voltage at the point in common between the components d9802, d9801 and q9802, a voltage well below 1.6 causes the backlight to trip, in the tests sound q9802 was removed from the circuit with this, the voltage returned to around 3v at this common point of the 3 components, this with the PCI disconnected from the main | Left without the q9802 | Direto no defeito |
| SAMSUNG | UN39EH5003 | Doesn't work | Defective +5v integrated circuit | Measuring the voltage at the remote control sensor socket it was 2.8v. Following the trail of this voltage I reached the defective IC202 integrated. | ELETROFEPAR |
| SAMSUNG | LN40C530F1M | Backlight keeps blinking like shaking | Replace dp 804 | Leaky diode | DANGRA ELETRÔNICA SÃO PAULO |
| SAMSUNG | PL43F4000 | Sometimes it turns on, sometimes the LED doesn't even light up | Moisture in the series resistors at the ac input | Resolve | Carlos Eletronica JL |
| SAMSUNG | PL43F4000 | Flashed standby, remained lit and did not obey remote control | Sem 15v ,vs e va ,5v normal | Photocoupler connected to qs807 at power supply | Hndrsn |
| SAMSUNG | 43NU/RU7100 | Power supply has blown fuse | Fet ey18 (you can use 13nm60) cp801 and cp805 swap the two, measure between drain and power supply if it gives 500Ω on both sides the pwm ci is also burned (fa1a60) | HP eletrônica | |
| SAMSUNG | UN50MU6100 | Blinks stby, and LEDs blink but do not turn on, tsound is no sound or image, measuring at the main 12v power connector they oscillate | Fuse f233, which goes to the output of ci q211 near the connector, open and shorted smd capacitor on the right side of the v-com, position c20, I replaced it and it was perfect | Eletrônica Portugal | |
| SAMSUNG | PL51F4000AG BN44-00599A P51HF | Normal power on does not generate video, slight blinking | Defect on the power supply board, mosfet transistor qx854 partially shorted | Test before ysus plate, plate | Eletrônica Sorriso Maike |
| SAMSUNG | LN40B530P2M | Does not turn on (normal power supply) | C207 short (it is next to the ic8005 memory) | Capacitor elimination | duc40rj |
| SAMSUNG | UN65HU8500GXZD | Doesn't start. Defective standby power supply. defect caused by the plastic underneath the PCI which rots and releases conductive oil and which also corrodes the board | Replacement of the IC pwm of the standby power supply s3330 position ics801 and the 1Ω resistor position rs801. Clean the board thoroughly and check for possible corrosion spots that could cause other defects on the board. | rafaelmoraes99 | |
| SAMSUNG | PL43F4900 | Sometimes it doesn't turn on, it doesn't even light up on stand by, sometimes it turns on | Do a test with a thermal blower or a head heater on the main board, if it gets hot and turns off, replace the capacitors c1024 and c1025 with 10uf/25volt electrolytic capacitors, note: observe the polarity, just find the negative side with a multimeter on the device's chassis | reginaldo moronte,eletronica junior caldas novas |