SAMSUNG TV Repair: Common Faults and Solutions.
Search: SAMSUNG
Results: 3754
Results: 3754
SAMSUNG Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG | LN32C550 | Turns on standby, does not start. | Z1031a(i203) power supply de z,zv em 1,shtv. | Replace ic203 | TVPAULO |
| SAMSUNG | UN32J4300AGXZD CA07 | Does not turn on, only standby | Capacitor c272 or c273 shorted, close to the hdmi connector | After changing the capacitors, the TV returned to normal operation. | EasyTech |
| SAMSUNG | CL21Z58MQ | TV works normally, but when turned on the next day, when you press the power key, the LED goes off and the TV doesn't play | C846 (100mfx25v) with low capacitance | Replace the 100mfx25v c846 | ELETRÔNICA CARVALHO |
| SAMSUNG | UN46D5500 | It doesn't turn on, it doesn't light up the LEDs. | Note, don't be fooled, this model when we remove the cable that goes from the power supply to the main board, the LEDs don't light up like on other Samsungs, so it's very deceiving, to find out, you only have a main board to confirm. | Replace main board. | MIGUELTV |
| SAMSUNG | PL43E400U1G | Image flashing, power supply pulsing voltages vs etc... | Resistor smd 200k alterado | Replace resistor rp828 (it can be any other in the same circuit, which obtains the same value.) | Weslley (UNITEC) |
| SAMSUNG | LS22EMSKUMZD LS24EMSKUMZD P2270HN P2470HN | The image disappears after use, turns off the backlight and the sound remains normal. | Inverter transformer on the T301 power supply board is faulty. measure output impedance, if it is much below or much above 1k, it is the likely defect. Also check for a possible faulty display lamp. | Changing the t301 power supply transformer. | rafaelmoraes99 |
| SAMSUNG | LN32A400 | TV turned off the lamps after about 5 minutes on | Lamps with natural wear generated oscillations causing the ovp protection to be activated | Remove crazy zenner zdi803 from ovp line | Edmilson |
| SAMSUNG | 32J4500 | No image,vgh na v-com 0 vcc | Q3 on v-com, change without testing | Roberto Consertos | |
| SAMSUNG | PL50C450 | No image, normal sound. | Y-sus board with burnt 30f123 transistor. probably some technician placed a buffer board that was shorted and burned the ysus. | Replace 30f123 (30f124 won't work, it will be pigmented). Furthermore, if you can, replace the rjp30e2 and rjp63k2 | PL Eletrônica |
| SAMSUNG | HT-C460 NT | Doesn't start. - inoperative power supply | After changing all photocouplers. check smd qm3 at power supply | Replace ( qm3- ksc1623l ) | PEDROTEC |
| SAMSUNG | LS17HAAKS | No image | At the power supply, 3 820uf 25v capacitors swollen and an open 3a fuse f301 hidden under the glue | I replaced them with 3 1000μF 35v fuses and replaced the fuse f301 | rkdapper |
| SAMSUNG | UN32A660 | The red STBY LED lights up but it does not accept commands and does not turn on. | Short on the remote sensor board. | Replace buzz or remove. | Lira |
| SAMSUNG | UN32EH4000G | Does not turn on LED does not light up | Shorted dm858 (sr320) | Replace diode | matieski |
| SAMSUNG | UN32J4300AG | Dead | Open fuse and shorted capacitor on the 19v line | EDUARDO TOMAS SILVA | |
| SAMSUNG | 32EH5000 | No image | Yash on vtson | Roberto Consertos | |
| SAMSUNG | LN32R71B | TV doesn't turn on. standby LED lit directly. | Six (6) power supply board electrolytic capacitors with altered ESR. | Check the electrolytic capacitors, and replace them if necessary. | leandrorocha |
| SAMSUNG | CL21CM21MQ | Turns on, works little, closes on the sides and turns off | Cr404s 681k/2kv next to d402 | Replace with new | FH solutions |
| SAMSUNG | MX-F630ZD | Device showing protective message | The aic2 audio output integrated (tas5342a) was removed and the message did not appear, when installing a new integrated the message was displayed again. | All the gaps between the CI pins were scraped as tsound was a lot of carbonization on the plate due to the heating of the part. This scraping was done with the tip of tweezers and assisted by an electron microscope for good visualization. Once that was done, I put the ci back in and the device started working normally again. | José Luiz Enguer Pereira |
| SAMSUNG | MX-F630ZD | Device showing protective message | The integrated audio output was removed and the message did not appear, when installing a new integrated the message was displayed again. | All the gaps between the CI pins were scraped as tsound was a lot of carbonization on the plate due to the heating of the part. This scraping was done with the tip of tweezers and assisted by an electron microscope for good visualization. Once that was done, I put the ci back in and the device started working normally again. | José Luiz Enguer Pereira |
| SAMSUNG | MX-F830/ZD | Device completely inoperative. | Shorted mosfet 17n80c3 | Replace o par qm801s e qm802s 17n80c3 e o icm 801 npc1379. | andredinho |