SONY TV Repair: Common Faults and Solutions.
Search: SONY
Results: 20066
Results: 20066
SONY Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SONY | HCD-GT3D | Cutting only the voice boxes, sub playing normally | Ic914 | Replace the same one, underside main board | BARBADINHA |
| SONY | KDL-50W705A RB1G | Flashing standby led 8 times | The service manual states that it is a software defect, but in my unit, it was a shorted capacitor on the top of the main board, close to the ic2408, next to the varicap. | The capacitor was replaced, the TV turned on again, but the display was also defective, a shame. | Eletrônica ATM |
| SONY | KDL-32BX425 | TV does not turn on, standby LED blinks twice. | Shorted inverter board mosfets | I replaced the mosfets with new ones from a donor board. | Adam Kevin |
| SONY | MHC EX880 | Dead | Dz968 | Zener diode in worship, | Sivaldo eletrônica |
| SONY | HCD-RG121 | I'm sound | No sound stk good, no power supply to the output relay | Replace ic371 on side plate | BARBADINHA |
| SONY | KDL-40EX605 | In sby red LED oscillates 3 times, power LED turns on, green LED goes off, red LED oscillates 7 times. | Shorted hdmi ic, replace | CLÓVIS, caphqz,eletronica.com | |
| SONY | MHC-V5 | Protect league 03 | Dirty plate full of dust | I cleaned the amplifier board, the box returned to normal. | Fernando técnico |
| SONY | GPX77 | Error 04 | Burnt outlet | Replace the board or try to do maintenance. Note: if the MOSFETs are toast, I find it very difficult to restore | Stiltec |
| SONY | KDL-48W655D | Without backlight and red LED flashes 6x | Blown fuse below the metal capacitor next to the large coil, measuring the meshes it connects will not show any short, but if you measure it itself it will be open. | Replace the fuse and evaluate the bus, in my case the bus was burnt. | Jailon |
| SONY | N160A006P | Turning off after a few minutes | Ci u101 (mps1880) | Replace ci u101 (mps1880) | Deo eletrônica |
| SONY | N160A006P | No voltage on the stand-by connector | No power arrives at the ci (u601) | Open resistor r820 (01b) it is 1k | Deo eletrônica |
| SONY | KDL-32CX525 KDL-30CX525 KDL-32CX725 | Led flashing 3 times, after removing the hdmi ci (shorted), it started flashing 8 times | To display an image and function, the HDMI ci must be operational, otherwise it will flash 8 times, a code that doesn't even exist in the service manual | Replacing hdmi ci | davi.sls |
| SONY | N160A006P | All normal voltages in stand-by, when activated everything dies | Zener diodes (802, 801, 804) of 720 and the ci u601 (sh2h0019) | Deo eletrônica | |
| SONY | KDL32BX355 BT4HA006397 | LED blinks twice | Three 680k power supply resistors | Eduardo Leal inventor/LOJA eletro 27 995044275 | |
| SONY | KDL 32BX | LED blinks twice | Check r9112, r9102, r9103, r9810, r9811, r9812 | Eduardo Leal inventor | |
| SONY | KDL40NX655 | No sound, or sound keeps coming and going | Change headphone connector (green connector) | <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> | |
| SOM SONY | MHC- TODOS OS MODELOS | Access panel no longer turns on | Leaky front keys | Replace all the keys, problem resolved. | Fernando técnico |
| SONY | GT 3D | Entering protect 3 | 1 remove the jack from the internal speaker, even though it beeps on the multimeter, it may be shorted or torn, remove it and run to the hug, just have it reconditioned, it will be great | Marck eletronica sao carlos | |
| SONY | MHC RG 290 40L7420 | Turns off but does not show the demo, the standby blinks on the display | When turned off, standby flashes but does not show the demos | Severino Ramos Nunes Juvenal | |
| SONY | KDL 42W655A | Blinking 5x | Remove and clean the cable | Cleaning the lvds cable contacts and board connectors. |