Samsung TV Repair: Common Faults and Solutions.
Search: Samsung
Results: 3759
Results: 3759
Samsung Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG | UN50TU8000G | Turns on, lights up LED bus and turns off, no image, stays in this loop | I saw several videos trying to isolate the cause with the famous tape on the flat, that procedure of searching until you find a point that releases the display short and the TV releases the image. | I couldn't do it that way, because the short was in the first left flat, that is, looking at the TV lying on the counter with the screen down, the flat that was preventing the TV from working was the first one on the left side. on the left side vcon board tsound is the test point "vgh", the track of this vgh that goes to this flat was cut and the TV worked perfectly without any scratches on the image, to make the cut easier the cut was made close to the r44 on the left side vcon board, please note Tsound you have the vgh point test and the cut I made right after, that is, I will remove this vgh reference that goes to the first left flat... | MIGUELTV |
| SAMSUNG | LS20CFSKFMZD | Turn off fabric | Place a 39k resistor from ground to pin 3 of the inverter ci | Velk JVM | |
| SAMSUNG | UN32F5500 | Does not turn on or turn on standby | Identified the following burned components (fuse 5a, qm801cs - stf10nm60nd, icm801 - s3310) | I replaced the components above, instead of the (10nm60) I used a kp11n60, instead of the s3310, I used an s3330, taken from another scrap Samsung power supply, everything worked 100% - note; merits also for waterfall electronics | CDS_DIAS / LED TECH |
| SAMSUNG | LN32D450G1G | LED flashes 3 times TV does not turn on | Q202 na pci principal | Replace the same | Williangb robista |
| SAMSUNG | UN32EH4000AG | Duplicated and flickering image | Remove r25 and r37 | In my case, just removing the r25 and the r37 solved the problem. clean image. | bileu |
| SAMSUNG | UN50NU7100G UN50NU7100 | Display problems, tsound were shadows on the right side of the panel, backlight ok | This Samsung model has this type of display problem a lot. | The lateral cofs were removed on the right side wsound the shadows were present, detail, start removing them little by little with the TV on to see the result, it is necessary to see the colors to continue removing the cofs | Hugo |
| SAMSUNG | LN40A550P | Does not turn on, just LED on, no back light | Placa principal, sem 3,3v no ic tmds351 | Replace tmds351 | TUROW |
| SAMSUNG | LN40D503F7GXZD | Red image | Tsound is an image but it is red | Alan | |
| SAMSUNG | T27B350LB | Restarting | Cable that connects the power supply board to the main board | Remove it and clean the card input connectors and the power supply board. it worked for me. the TV has returned to normal | flavio |
| SAMSUNG | PL51F4000AG | Stretched image | Signal board replacement | Replace the position of the zr 869 fhd to r860hd or vice versa | paulo rps |
| SAMSUNG | UN32T4300AG | Totally inoperative | Shorted diode under the processor heatsink | When removing the diode the board started working again | Eletrônica JJ |
| SAMSUNG | UN55F7500 | Relay keeps disarming | Ci in short | Replace ci slc1013m | cleber lima rs |
| SAMSUNG | PL51F4000 | It doesn't turn on, it only has pson voltage 5v | In my case tsound was only 5v voltage pson grounding no voltage appeared tsound was no 5v, 15v, go, vs | Replace qq806, 807(std5915) resolved | speedtec |
| SAMSUNG | LN32B350F1 | TV doesn't turn on without STBY. | Main board short. | SMD ceramic capacitor shorted, blocking the c2028 board, leading to the sound output. | RNSPTEC |
| SAMSUNG | UN65TU7000FXZA, UN75TU7000FXZA, UN43TU7000FXZA, UN55TU7000FXZA, UN50TU7000FXZA, UN70TU7000FXZA, UN75TU700DFXZA UHD UWL02 | After a software update on the television, a usb error message is displayed. | To complete a software update, the tv must reboot twice in order to apply the update. if the usb is removed prematurely or an unexpected error occurs during updating, the update may fail and the below error will be displayed. | Service method: download the latest software version from samsung.com and install it manually via usb. please do not remove the usb or disconnect power until the tv reboots the second time. | Martin |
| SAMSUNG | UN65TU7000FXZA, UN75TU7000FXZA, UN43TU7000FXZA, UN55TU7000FXZA, UN50TU7000FXZA, UN70TU7000FXZA, UN75TU700DFXZA UHD UWL02 | Image distortion | Update t-con data. do not replace any parts | 1. download software version 1082.1 or higher from samsung.com 2. unzip the file and save the folder t-ktsu2akuc to the root of a usb drive and bring the usb with you at the time of repair 3. insert the usb into the usb port on tv 4. go to settings → support → software update → update now to start the update. please wait for the update to finish 5. the tv will power off and back on when the update is done 6. after the update is done, the tv needs to be cold booted again manually for t-con to be updated.
| Martin |
| SAMSUNG | PL42B450 | Does not turn on without stand by and without voltage on the main capacitors | Checked cold soldering on the dx807 transistor (it is on the right side of the power supply) | I solved him and the others. and the TV started working again without having to replace a single component | Macro Eletrônica DF |
| SAMSUNG | PN43H4000AG | Does not turn on and the standby LED is off | Change the photocouplers on the power supply board | D.a redetech | |
| SAMSUNG | PN43H4000 | Every stop, not even the LED lit up | Check all the jumpers because in my case they were all broken and also check under the heatsink as tsound are some hidden tsound ok good luck that was my case I fixed it and went to dim dim | eletronica publisom | |
| SAMSUNG | UN40J5200 | Black light flashing | LED bars shorted to the chassis | Mariano |