Samsung TV Repair: Common Faults and Solutions.
Search: Samsung
Results: 3759
Results: 3759
Samsung Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SAMSUNG | PL60F5000AG 60FF YM YSUS | Does not turn on, LED flashes, ysus board defect technical repair (edited) | Replace q5024, q5025, q5002, q5003, q5034, q5005, d5022, d5043, c5027, c5028 e medir r5097, r5084 | The following tips are for technicians, avoid doubts, replace the parts with the same ones. preferably all the ones I mentioned. | Maike-Sorriso(MT) |
SAMSUNG | PL60F5000 60FF YM YSUS | Red LED flashes, does not turn on, ysus defect | Replace q5024, q5025, q502, q503, q5034, q5005, d5022, d5043, c5027, c5028 e medir r5097, r5084 | The following tips are for technicians, avoid doubts, replace the parts for the same ones in the description above and go for a hug!! | Maike sorriso-MT |
SAMSUNG | UN32J4000AG | TV doesn't turn on and doesn't even light up the stand bay | After testing the board and not finding a defect, I checked the on/off button and it was shorted when changing the TV and it worked normally. | beto_eletrotec | |
SAMSUNG | PL51F4000 ORESTS | Does not light up backlit | Power supply change | Alextecnico | |
SAMSUNG | LN46A610A1R | No image | Turn on but not from the image | Renato | |
SAMSUNG | NG32ND450S | Nor etc. mortar | Replace 3v3 regulator, smd sot23, it is on the 5v coil side, the board only has 5v and 12v. | joaomvjr | |
SAMSUNG | 55MU6100G Y18-Q7F 49" | Backlight turns on normally, has sound and no image. display voltage of 3v3 with 2.5 and without the display voltages voff, von, vgh, vgl... | I don't know the cause of this problem, but the customer reported that the TV stopped after a strong storm... | Fuse f223_ut open on the main board close to the power supply connector. Be very careful when analyzing because these models give a lot of defects in the display that have the same symptom, so it could be a simple defect in the main one and end up making a mistake and condemning the display. always analyze carefully | SV Eletrônica |
SAMSUNG | PL43F4000AG PL51F4000AG | Sometimes it turned on sound and image: and sometimes it just stayed on stand-by | Protection triggered | Remove the two transistors from the pci f type (bc) that provides protection and that's it | Airton Filgueira |
SAMSUNG | CL21Z50MQ | Cushion defect | D408 shorted | AIRTON. PARAIPABA CE | |
SAMSUNG | CL21Z58MQ | Doesn't start. standby flashing | C 846 100mf x 25v com esr elevada. | NEW PEK ELETRÔNICA | |
SAMSUNG | UN32EH4000G | With normal audio, black light access and no plot (absence of image). | Smd c14 capacitor with leak on pci vcon. causing absence of avdd 15vcc and vone 28vcc power supply. | Replace smd capacitor with another equivalent, which can be 10μFx35vcc(jm). | Eletrônica JM |
SAMSUNG | UN43J5200AG | No image, backlight on | Capacitor changed on the v-com c003 board | Just remove the aforementioned capacitor, | Emerson Lima |
SAMSUNG | CL 21Z50MQ | Inoperative, with voltages pulsing. | R 821 of 100k open is close to the fly back | Replace. | Ferraz |
SAMSUNG | LN40D503F | Tsound is sound but no image, the lamps don't light up | The cause was the r1815 is close to the pc803s | Just replace and run for the hug post your tips sound too help to be helped ok | naelson silva gravata pe |
SAMSUNG | UN55C6900 | Does not turn on, relay knocking | Arming the power supply outside, the pfc circuit worked but the 12v was not generated. | Qm851 replaced | Lucas |
SAMSUNG | UN55D8000 | Intermittent on and off | Defective led bar | Stiltec | |
SAMSUNG | T22A300 | Does not turn on blinking stand by led | Photocoupler | reginaldo moronte,eletronica junior caldas novas | |
SAMSUNG | UN40H4203 UN40H4200 | Burning the LEDs reduces the current | Https://youtu.be/7odeogttosq | Eliel Batista | |
SAMSUNG | 2033SW PLUS | Screen turns off seconds after turning on | Weak light bulbs - remove lamp protection | Place a 10k resistor on pin 10 of the ci bd9893f and ground | HAHNRAHN |
SAMSUNG | HT-Z 210 | Turns on, then immediately activates the protection. Check at the power supply if tsound are voltages in the connector that goes to the audio card. +12, -12, 29v. | In my case, the 12v voltage was missing from this connector. see possible short in the 6000ufx6.3v capacitor. | Replace o capacitor 6000μFx6.3v | arock |