Sony TV Repair: Common Faults and Solutions.
Search: Sony
Results: 20067
Results: 20067
Sony Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SONY | KV1217 | No uhf, replaced tuner | No uhf. | ||
| SONY | KV1214 | Picture interference | Interference in shape of two vertical lines on left side ofscreen. waveform at input to blanker stage was distorted. | ||
| SONY | KV4000 | Tuning would not lock | Will not lock on station when cold, after unit warms up willwork properly. found waveform at pin 8 of ic134 incorrect. | ||
| SONY | KV3000R | No remote functions | Upon inspection after delivery to dealer it was noted thatthere were no remote functions and only limited manual functions. powercame on immediately after engaging master power switch and set could notbe turned off except with same. the only other manu | ||
| SONY | KV2643R | Retrace lines, replaced r749 | Excessive brightness/retrace lines. rv2203, rv304, rv701 haveno effect, pin 12 crt = 850v. | ||
| SONY | KV2145R | Dark picture, resolder r054 | Raster goes dark with sound bars, sound normal, then normalpicture jumps back. found r054 mounted on the print side, cold soldered. | ||
| SONY | KV2145R | H tearing & flashing, resolder anode lead | R067 on mf board overheats. noticed intermittent horizontaltearing and flashing across screen. found anode lead which is a plug intype, was not making firm contact. | ||
| SONY | KV1946R | Shut down, l503 broken off | Set would go into shut-down mode immediately at turn on.i verified horizontal oscillator and b+ circuits were operating properly.i then noticed that the coil l503 was broken off of the connection onpc board. | ||
| SONY | KV1923 | Tuning shifts | Channels would program correctly. if set was on channel 2and moved to channel 8 then back to channel 2, channel 2 would not comein. same with channel 8 when set was returned to this channel. thiswould also happen if the set was turned off and back on. | ||
| SONY | KV2647R | Shut down with jig, ground hvr | This particular unit shut off instantaneously when power wasturned on. it happens only when chassis was attached to the jig. most ofthe time technicians spent useless hours to find out that the ground onthe hvr was missing (usually a screw grounds the | ||
| SONY | KV2645RS | Pin cushion, add resistor in series with r809 | Pincushion correction at top and bottom near the corners isalmost null. -hq comments: to correct the problem place a 15Ω 1w resistor inseries with r809 (100Ω 1w) and readjust pin phase and pin ampcontrols. | ||
| SONY | KV2643R | No channel lock, replaced c206 | Except on low band this unit keeps on scanning stations.ch. 2, 4, 5 could be tuned in but slightly have weak video (slight snow).found c206 leaky causing a drop, at pins 26 and 28 to 1.7 volts insteadof 4.6 volts. | ||
| SONY | KV1546R | Vert roll, intermittent vert collapse, replaced c508 | Set operates fine for 1/2 to one hour then starts to roll,then vertical collapse. found c508 improperly installed (reversepolarity). | ||
| SONY | KV1217 | Picture distortion, see modification below | Horiz. centering adjustment will not shift picture far enoughtowards the right. center adjustment only expands the picture. -hq comments: try the following circuit modification. place the horiz.centering r. position. the r1, r2, c1 values shown shoul | ||
| SONY | KV1207 | No channel look | Set changes channel by itself usually ending on ch. 13position. | ||
| SONY | KP5040 | Incorrect mechanical function, use of loctite | When unit was turned on the mirror door would extend about2/3 of the way out and start clicking. the motor would continue to runand not shut off. disassembly revealed the retaining nut on the driveshaft had worked loose allowing the left hand side door | ||
| SONY | KV2647R | No picture, open r057 and prescaler, | R057 resistor open (mf board). no problem found in reg.circuit. solder splash on feed thru terminal of prescaler. | ||
| SONY | KV2645RS | Tuning would not lock, replaced s2262 | Tv would continuously scan through all channels. foundchannel up button closed. | ||
| SONY | KV2645R | Dark picture, replaced r-751 | Dark picture like weak crt. found r751 changed value. | ||
| SONY | KV2601 | Part number missing | Servicer has kv-2601 with spark gap on c board shorted -schematic designation sg. the part number was omitted from the servicemanual of all the above listed models. -hq comments: the spark gap in question is not available as a separatepart. it comes w |