Search: LG
Results: 4834

LG Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
LG42LB7DF
Sometimes it turns on but the image stays darkPower transistor 07n60c3 location q706 check q707 tooSwapping for a 12n50 power mosfet, solved the problemCELSOKAYRAN
LG CM4320
On/mute/offMi case was zd905 short zener 20vRafael da telesateleletronica
LG 21FU6RL
Arm and disarm wanting to ocstilR515 is or r516 open on secondaryReplace and run for the hugBynho teck
LGCM4430
Tsound was no sound after 2 minutes it turned off and the message displayed on the display: s-protection20v zene diode zd905 shortedReginaldo Alves
LG50PA4500
Negative imageOpen resistor na and its 2r2Resistor de 330r smd na yrogerio_federal
LGCM4420
Works normally but no sound comes outPvdd 0volt diode zd904 alteredReplaceo zd904 problem solved.samuel leite
LG42SL80YD
Only the backlight on with no sound and no imageReflow processorMenegat eletrônica
LG26LG30R
Stopped, when turning on the LED lights up blue and nothing1.2v low supply - regulator on the bottom of the IC 1103 board.Remove d1103 and put a jump in its place, just run for the hugVICTORINO
LG32LH20R
Turn it on then turn it off, only the sound remainsInverter boardHP ELETRONICA
LG50PA4500
When pressing power the TV turns on and then turns off without generating an imageTransistor q601 burned - thermistor th101 burnedReplace the twoDeivid Vanzuita
LG47LG60FR
No video signal; antenna, cable, etc... the screen lights up normally (with sprinkles). when injecting signal, it turns off immediately.One of the probable and quite common causes are the electrolytic capacitors c1105, c1109, c1110, c1118, c1128 and c1141 (100mf/16v) c1133 and c833 (10mf/16v). all on the signal board.Replace them without measuring. good luck.<small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small>
LG21FU1RL
CW81A
Vertical closedR- 301 open 18kReplacementlucinaldo
LGRAD 114
Doesn't startOnly led onJosé Adilson augusta
LG47LE5500
TV turns on, hangs on the LG home screen and doesn't come out of it.LockThe BGA processor was resoldered as it will show cold soldering between the BGA terminals in its operation over time. remove the TV board remove the heatsink apply flux under the bga terminals and with a thermal blower at a temperature of 280 to 300 degrees heat until the solder enters its liquid state, being careful not to displace the bga. Once done, wait for the board to cool down and assembleAdriano Miranda
LG29FE8RL
CW62C
Relay arms and disarms but does not turn on the TV, LED is off. Tsound is only voltage on the primaryDefect ic 802 photo couplerOkJOCIMARIO
LG32LD650 42LD650 42LW5700 47LV5500
Normal power supplys.does not turn on, with LED flashing slowly or with colored outlines in the image or with thick lines in the image.metallic microprocessor with loose pins.remove heatsink.protect parts around the micro with adhesive aluminum tape.with thermal blower at 300 degrees , heat the computer for exactly 90 seconds. After it cools down, replace the heatsink.With this procedure and due to the high cost of the new board, it was possible to recover several boards with perfect functioning.gesuino
LGRP 14CB 20A
Washed screen, very clear and matte image, normal audio.Sparking in the tube socket.Socket replace, focus adjustment.Geraldo de Petrópolis
LG42LS5700
Turns off intermittentlyDamaged LED on the busLED replacementDiego Boeira
LGCM8350
Turns on, but no audio outputPfc voltage was low. cause: leaky pnp transistor ktn2907as (zh).Just replace it and the problem will be solved. component position: q910(FELIPE) PRO PC Eletrônica e Informática
LG14FK3BR
Vertical closed at the bottom and stretched at the top like the image is folded at the bottomR=305- 12k changed measuring 29kReplaced and solved the problemAntonio Carlos (Eletrônica Renascer)Boa Vista do Gurupi-MA