PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PCM2051 | TV with sound; no image, no brightness | C 801 on the trc board | After the replace, everything shine appeared | ELETRON ICA ROCHA FERNANDO ROCHA |
PHILCO | PCM 1444 E OUTRAS | Mirror image | R 718 open | Master | |
PHILCO | TPF29S4F | Closes image in the corners, cushion or cup effect, does not correct pincushion. | D1702 with oxidized terminal glue. | Bruske | |
PHILCO | TP14U56 | Turns on and after 3 to 5 seconds turns off. | Bad solder in the photo coupler region | I observed that all voltages were normal. and I noticed that it oscillated and when it was about to light up the tube went into protection and the LED kept blinking. That's when I suspected the photo coupler region. As I didn't find any defective components, I decided to re-solder that region and it was ok. | Tec vídeo |
PHILCO | PCM2044 | TV turns on and off by itself, sometimes it takes a few minutes | R713 open | juci | |
PHILCO | TP-2054 | The device is turned on, the screen turns red with incriminate traces, after a few seconds it goes into stand-by, | Metal film resistor, value 10k, on the kinescope board, referring to the red cannon drainer transistor, replace it, it is ok. | CLÁUDIO RIBEIRO, TECNOSAT ELETRONICA E INFORMÁTICA, JATAÍ-GO. | |
PHILCO | TPF2130 | It turns on but when the relay goes off a brief image appears with the frame closing horizontally, it goes to stand by with the LED flashing. | C701 (horizontal deflection) auterated | Replace the c701 (8.2 nf/1.6kv) | Ricardo Moreno |
PHILCO | PCS 2956N | High voltage spikes and turns off | Width defect, replace 8n2 and 4n7 ceramic width capacitors and increase the vertical output transistor decipher (2) | Prado | |
PHILCO | PC2956 | Tsound is no voltage in the secondary of the power supply, it just pulses. | C-921=1k per 1kv of shorted disc, only replace with one of the same value, if not the voltage variation. | It was replaced for one of the same value and it was... ok. | Armando da Eletrônica só Tv. |
PHILCO | PCS2952 | It keeps beeping, beeping and the LED is blinking. | Q 902. | I started it off and it worked. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | TPF 2140 | It doesn't turn on and it doesn't work on standby. | C 930 with leak in the power supply primary | levilp | |
PHILCO | PCM2044 CPH05 | Vertical fexado. | R.602 | Replace. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | PCS-2956 CP-01-LR01 | Power supply does not start and chopper driver smokes on pin 7 | C922 short (1.0 nf) I replaced it and the problem was solved. | Note: as the c922 is on the pulse line (130v) the power supply activates and disarms successively. | Tecnogil Eletronica |
PHILCO | PT20V56 | Vertical beam and then switches off | Ceramic capacitor c614 | ELETRONICAAC | |
PHILCO | TP20V56 | Vertical beam and then switches off | Ceramic capacitor c614 | Ac electronics | |
PHILCO | PCS2952 | Dark image with little contrast | C 716 short /r706 open | betoteck | |
PHILCO | TPF 2121 | Morta (nem da stand by) | D908 e c914 | Obs: mude c914 p/ 1000y/35v | VSE Eletrônica(Ádrian) |
PHILCO | TP2054 | Does not turn on, LED is off. | R 911 amended. | Replace. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | PCM2044 | Lack of sync and drizzle | C205 - agc and c702 sync. I changed the caps. It started working normally again. This email address is being protected from spambots. You need JavaScript enabled to view it. | The two electro/capacitors with high esr. | vxm |
PHILCO | TP1452N | Does not turn on, stays on standby | When the TV is on stand by with the LED on, replace the zd923 4.7 volt diode and the zd922 3.9 volt diode. | Edilson Ribeiro |