PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PE14H | With low supply +-20v on b+ | Q881 leaking. | Replaced by bf422, pay attention to collector and emitter. | eletronicaoeste |
PHILCO | TV PH21C | Does not turn on, LED keeps flashing, +b with 20v | Q881 2n5551 | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILCO | TP2010 | Lines at the top of the screen and rainbow effect. | Replacement of ic601 (tda8177) | Replace the c.i. The equivalent or replacement tda is tda9302. | R-TEC Eletrônica |
PHILCO | PH 14D | Stand by LED does not come out blinking | Q881 / r882 / r881a / c883 / c882 | Replace q881 2n5551 por mps-a42 / r882 - 22k / r881 - 10r / c883 - 470/25 / c882 470/25 | eletronicaapolo |
PHILCO | PH 21 SS | Dark canvas about 10 centimeters at the bottom, top part of the retrace lines | I changed the 24c08 eeprom and it was just luxury!!! | Ray Ferreira | |
PHILCO | DV-P4800 | No image on normal output, just scrambled image on component video output | Memory 24c02 | Changing it doesn't even need to be recorded | ELETRONICA GAZZIN - felipe |
PHILCO | TP 2053 | Turns on and off and flashes stand by | R 919 secondary power supply (must be changed) | ||
PHILCO | TPF 2902 | Expanded image, and like a slight cushion defect. | The 6.8uf c707 electrolytic was exchanged for 47 uf, close to horizontal. | Leandro | |
PHILCO | PC2041 | No image with sound | C301 0,47mf | Replace | juci |
PHILCO | PCS-2976 | Just turning off, the LED blinks and only turns on after taking it out and plugging it into the socket. | Power supply regulator q901 11n60 faulty | Replace q901 without measuring | eletrônica reis |
PHILCO | PH29US | Philco TV closed from the middle down | Faulty memory | Replace without wasting time for a new one, it can be 24c16 or 24c08 | Sergio |
PHILCO | PCS-2952 | It doesn't start, STBY LED flashing, +b voltage [120v] only drops about 12 to 15 volts. | C949 [220uf/ 200v] seco. | Replaced for a 470μF/200v one without any replaces. | Altevirlima_Valparaiso Eletrônica_PA |
PHILCO | PH 21 E | Tall and short | Diodo zener 5v6 (d805) | oilec | |
PHILCO | TP2054 | When trying to turn on the power supply it would be normal, then it would go down and there would be a noise from the speakers. | Transformador driver horizontal t702. | @gepe | |
PHILCO | TP-2920 | TV does not turn on (inoperative) TV in stand by When turned on, the LED flashes and the power supply does not start, remaining in stand by. | The polyester capacitors 1701 and 1703, both 6n8/1600v, which are located in the TV's primary power supply, were replaced. | MAGDAEL | |
PHILCO | PH 14D | Turns on the key and gets an intermittent cricket sound heating up the transistor s. horizontal | Fly back with malfunction | Just replace for another 0232 | Cláudio Jardim Paulista Bx |
PHILCO | TP - 2054 | With the image flickering and after a few minutes the power supply only turns off 90 volts | Check the 12v zd904 zener diode | To replace | VERANILDOCC |
PHILCO | TV PH21 | Does not demagnetize | Rt801 | ÁdrianChapadãodoCéu | |
PHILCO | TPF2130 | TV turns on normally after a few minutes it turns off, the standby LED is blinking | Capacitor c 918 e fotoacoplador | Replace the same | TIAGO.ELETRO-PB |
PHILCO | TPF 2130 | Closed horizontal | C713 open | Replace c 713 | juci |