PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PCM2046 CPH-5 | Does not turn on, or makes noise and turns off and on again | Capacitor c722 | C722 capacitor replaced | johnny busnadiego |
PHILCO | TPF 2130 | Sometimes the TV doesn't turn on, it just stays on standby, similar to a defect with poor contact | 1000uf/16v electrolytic capacitor c918, which filters the 12v supply, with little capacitance or high esr | Replace capacitor | AFONSO SANTANA |
PHILCO | TPF 2140 | When you turn on the power on switch, there is a noise in the speaker and the TV does not turn on. | Shorted vertical -12v rectifier diode d909a | Replace diode | AFONSO SANTANA |
PHILCO | TP2921 | With a chirp at the power supply | Micronas | This TV came into the workshop with the following problem, all the power supplys were low and it didn't light up, so I released the IC 805 and then I noticed that the power supplys normalized. Conclusion I replaced the microwave and the TV worked normally | zezinho |
PHILCO | TP29C21 | It turned on and at the same time it turned off, remaining on standby | D908 and d908 (cold welding) | Redo the weld | jvb |
PHILCO | TFP2940 | Turns on, protects and the LED blinks | Replace c 1701 and c1703 5n6?1k6 and adjust screen | Antonio Martis | |
PHILCO | TP2000 | C715 swap | This email address is being protected from spambots. You need JavaScript enabled to view it. | ||
PHILCO | TP2054 | Normal power supplys, when turned on it works for + or - 5 seconds, and goes into protection, (the panel LED keeps flashing) | C718 swap | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
PHILCO | TP 1454 | Vertical bar on the left side of the screen approximately 3cm | Change capacitor smd c 705 2n2 pin 16 of the micro does not measure can be replaced with a common ceramic | Replace c705 2n2 | fabiusmax |
TV PHILCO | TPF2121 | Only on stand by, with noise at the power supply. | Q901 faulty and d908 shorted. | edsomvideo | |
PHILCO | TP1452N | Fountain sobbing | C911 e c913 | Replace both if it continues, replace ic 901 | Elias2305 |
PHILCO | TP1452N | With colorful stripes across the screen | R708 (I replaced the vertical output, micro, tda) and it was just low voltage.... | Replace without testing.. | Elias2305 |
PHILCO | TP29C21 | Charging power supply capacitor, power supply does not oscillate | D915 from primary power supply | This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI | |
TV PHILCO | PCS2956 | Tv philco pcs2956 that the image is normal, but there is a strong noise in the sound of the channels as if it had an unadjusted aft coil. | I replaced the ic501 tda8843 2y then it was amazing. | bf.colatino | |
PHILCO | 2049 | When turning on, only the channel number (OSD) appears, increasing the screen the image appears, but the next day it is the same thing | Resolder all smd resistors on the tube board. | HP ELETRONICA | |
PHILCO | PC2048 CPH06 | Sometimes the TV doesn't turn on, it keeps banging and clicking on the speaker | Intermittent 9v power supply.. check all power supply and pay attention to the 9v inductor that presents this intermittent defect. | Replace blue inductor at 9v output | ELETRONICA ROBSON (DEBIQUE) |
PHILCO | TP 2920 | When turned on, it arms and returns to stand by, heating the filament, you can see who has video feed | Exchange c1701 6k8 and c1703 | itan (cabeça) | |
PHILCO | TP2921 | Turns on but after a while it turns off and remains on standby. I turn it on again after about 6 minutes it turns off | Change the c805 it comes from 22uf\160 change it to 47uf\160v also change q830 (replace everything without measuring ok) | Replace the c805 it comes from 22μF\160 replace it to 47μF\160v also replace q830 (replace everything without measuring ok) | Deusomar |
PHILCO | TVPH21B | Dark image when the TV or DVD signal comes in. Note: when there is no signal, the brightness remains normal. | Diode in4148 (vd 461) shorted on the abl line | marcelo de castro | |
TV PHILCO | PC-1445 | +b 95 volts does not turn on the TV, only with a humming sound at the power supply. | Resolved by changing c911 220uf x 160volts. | BF.COLATINO |