PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | TPF29S4F | TV arrived at the inoperative workshop. I found a diode on the yoke board with a short in position d1701, I replaced it with a new one, the TV started working again, but the screen had stretched corners, I tested the entire yoke board but everything was ok, I went into the service menu and more. it was a defect; Luckily, another TC Philco model TP2920 arrived which had the same chassis, so I ordered the yoke plate and put it in, it was still defective; So, look at the other board, there were two wires coming from the 706 capacitor position going out to the yoke board, so I did it from the other board; negative position of the capacitor n pin 2 of the cm 1307 positive n pin 1, then also change the resistor n position r 1702 to 47k then just joy ;8817 | Missing wire that connects the yoke with the position d c 706 | Remove capacitor c706 put two wires in its place connect socket cm 1703 which is n yoke + a 47k resistor | marcos melo cascavel ceara |
PHILCO | TVPH21SS | Doesn't start, doesn't have +b. | R520 of 120k open at power supply. | It was just a matter of changing it and it was ok. | FRANCISCO - ELETRONICA SÃO FRANCISCO This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | TP2920 | Turns on then goes into protection, LED flashes. | Exchange c1701 and c1703 | ||
PHILCO | PC2041 | Turning off after flyback replacement | Resistor r723 (27k) open abl line | ARAUJO | |
PHILCO | TP2052 | It doesn't turn on, or it oscillates and turns off and the LED keeps flashing | C706 6n8 leaking capacitor | I put another one it worked perfectly | FRANCISCO RS |
PHILCO | TP2053N | Blinking LED doesn't turn on | Shorted deflector coil | Replace the coil | francisco rs |
PHILCO | PC2013U CPH02 | Vertical closed | Capacitotor c 611 de 100uf/100v rim | Also replace c607 at 10μF/63v and c609 at 4.7μF/63v | francisco rs |
PHILCO | PCM2146 | Inoperative, stand-by LED flashes and does not turn on | Capacitor c905, replace as it is open | claudio e reinaldo | |
PHILCO | TP-2054 = TP-2053 | It doesn't turn on when the standby LED starts blinking +b at 109v it drops to 15v @@@ | Saida vertical tda9309 tv tp-2053 a tv tp-2054 vertical tda9302 a ou h | Help yourself, leave your tip ass.arni | ELETRONICA ARNI-LEOBERTO LEAL-SC |
PHILCO | TP-2054 = TP-2053 | Does not turn on when turned on, the standby LED flashes | D09, R10=47.0, R12=47.0 | ELETRONICA ARNI-LEOBERTO LEAL-SC | |
PHILCO | TP-2054 | E.a doesn't turn on LED keeps flashing @@@@ | D09, R10=47.0, R12=47.0 | Help yourself, leave your tip ass.arni | ELETRONICA ARNI-LEOBERTO LEAL-SC |
PHILCO | TP20V56 CP02R0 | Doesn't start | D909 in the power supply secondary | luiz g.silva | |
PHILCO | TP20V56 CP02R0 | Doesn't start | Power supply secondary d900 | luiz g.silva | |
PHILCO | PCM2044 | Verticalopen only 5cm from the middle upwards | C-613 pin 3 of vert output. 2n2 was with 1n6 | joaoxx | |
PHILCO | TP-2052N | Does not turn on, LED off, device inoperative without voltage on the power supply secondary. | Cold welding at the power supply. | Resolder r910, r909, d906 and points on the same power supply line. | celinvds |
PHILCO | TP1410 | Standby is on but when I turn it on it starts blinking but doesn't oscillate the TV only has +b 106 volts | 15 homs resistor burnt or with raw solder check it position r931 and it feeds the 1000mf x 16 volt capacitor take advantage and change it without testing the c918 | ||
PHILCO | TFP2902 | Horizontal shifted right side | Capacitor c732 smd 2n2 | ||
PHILCO | PCM 2044 05 | Vertical closed dark strip at the bottom | Capacitor 1000uf35v no esquema c610 | I replaced it, it was a jewel | dgspeg |
PHILCO | PCM2044 05 | Vertical closed dark strip at the bottom | Capacitor 1000uf35v | I replaced it, it was a jewel | dgspeg |
PHILCO | PCS-2956 CPO1LR01 | TV with no image and no sound; with line of retraces. | Irregularities in the ic101 (m37274ma), memory, blocked the system when activating the image adjustment in the menu. | After replacing the ic 101 (m37274ma), the device was ok. | clayton |