PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | TP-1454 | Turns on standby, but does not turn on | DS08 | Shorted diode, just replace it | This email address is being protected from spambots. You need JavaScript enabled to view it. Marcondes Jaicós-PI Ohm eletronica |
PHILCO | TP 2052 | Blinking led | Resolder smd components at the power supply | ÁdrianChapadãodoCéu | |
PHILCO | TP1454 | No video, screen with colored spots | R910 and 912 | If your phone is buzzing, replace d909 short | marcondes, OHM eletronica Jaicos-PI |
PHILCO | TP2052N | It doesn't turn on beeping without the +b on the flaybk pin | The cause was the shorted capacitor c924, sending the +b to ground. | I replaced the capacitor and the power supply armed, I hope this tip helps some friend on the forum. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | PC2043 CPH-5 | Turns off and buzzes | R706 e c716 | R of 10k replaced and c22n replace both | marcondes, OHM eletronica Jaicos-PI |
PHILCO | PCS2952N | Burned fusil | D909 d911 eo c904 | And cool file | josé da eletronica schayonara em florip |
PHILCO | PCM1443 | TV turning on the power supply and maintaining the 20v power supply | Causa dz904 | marcondes, OHM eletronica Jaicos-PI | |
PHILCO | TP 2010 | TV doesn't turn on, stays on stand by | 8n2 capacitor 701 | Ohm eletronica | |
PHILCO | TP1452N ? | Out of tune | C208, semi capacitance | Troar. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | TP1452N ? | Out of tune | C208 sem capacitance | Replace | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | TP1452N ? | Out of tune | C 208 without capacitance | Replace it. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | TP20V56 55 02 F6949 06 2 | Vertical heating, with some scratches on the bottom of the screen | Cold solders, on the IC pins and smd capacitors that belong to the vertical. and at two solder points that go to pin 1 from the vertical to the r612a. | I did the general repair and it worked normally again. | eletronica melo boa viagem ,ceará |
PHILCO | TP-2053 | Dark image then turns off and standby LED flashes | Cold solder on the terminals of the FC806a cable connected to the socket on the kinescope board | Resolder the f806a cable that is connected to the kinescope board | guaracy borges |
PHILCO | PCR 2049 | Does not turn on, horizontal noise | C704 (471/2kv) | MB ELETRONICA | |
PHILCO | PCS 2976 | Turns on and off with LED flashing until it burns out r917(2k2) | Cold welding d908 and d909 | Resolder and replace the resistor | ÁdrianChapadãodoCéu |
PHILCO | TPF-2121 | Horizontal burnt q701 | Replace q701 (bu2506dx) e c715 (6n8/1k6v) | Marcio | |
PHILCO | PCS 2976 | LED blinking very quickly | R917 open | 2k2 | ÁdrianChapadãodoCéu |
PHILCO | PCM 2046 | Cesa screen with retrace line | C719 was stuffed | Just replace, send you the tips as well because they help | serginhosond@yahoo |
PHILCO | TP2053 | Dead power supply | Ic 901 did not oscillate | betoteck | |
PHILCO | TPF2940 | When the TV is turned on after a few minutes, the image darkens at once but the sound continues. Turning it off and turning it on again returns the image normally and after about 10 to 16 minutes it returns with the same defect. | I removed the capacitor c60 9 of 220nf x100v which was measuring about 202nf on the capacimeter. and the c606 of 47nonofaraides x250 vlts apparently good on the capacimeter, but it was bad | I replaced the two c606 and c609 close to the vertical output (note in some cases you have to replace up to the vertical output number; tda 8177f) it remained file | This email address is being protected from spambots. You need JavaScript enabled to view it. |