PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | TP2052N | Replace these components and the device will work normally again. | Philco pcs-2976 dead, supply high (170 v) change resistor 917 (2k2) diode 908, d 902 (transistor type) ic 802 (photo-coupler) | Replace these components and the device will work normally again. | Elias |
PHILCO | PC20R42 | It doesn't turn on, it only lights up STBY LED, power supply ok, micro crystal ok | Reset circuit pin 7 of the micro, remove IC 104 and see if it turns on the TV pin 7 it must have 5v | By c of 4.7μF instead of ic 104, -pin2 and +pin4 | BRUSKE |
PHILCO | TPF2121 | When turning on it makes a noise on the flyback and it doesn't oscillate | D 908 shorted | Replace d 908 for an original | haecio |
PHILCO | PC-1435 CPH-03 | Blue screen with retrace lines | Shorted diode d701 | D701 diode replacement | somprimos eletronica |
PHILCO | PC2043 | Power supply does not generate | D905 shorted | Replace the diode and the TV worked normally | ANTONIO DO RADIO |
PHILCO REAL FLAT | TPF2940 | LED flashing and arming the protection | Opening the screen a little you notice retraction lines and then you arm the protection causing the led to blink | Replace 2 cap 5n6 / 1k6 c1701 c1703 | EPATEC-ES |
PHILCO | TP1453 | After turning on the TV, a line appeared on the screen and it turned off. | High power supply above 108 v | I replaced the 120k r 919 and everything was normal | ELETRONICA ROCHA |
PHILCO | PCM-2046 | It would turn on, the LED would flash, r720 was damaged, it would be replaced and it would burn again. | O problema era ic 601 tda-3653b | Changing it solved the problem, thanks | Eronaldo |
PHILCO | PSC 2952 N | When it turns on from high voltage and turns off | Changed the weak c - 712 6 k 8 / 1600volts | jaironuness | |
PHILCO | PCM-1466 | Image distorts in some channels | Changed c- 205 2.2/50 volts weak | jaironuness | |
PHILCO HITACHI | PC 1441 | The TV turns on and within seconds the vertical closes | Solution to the problem r 725 r 4r7 close to the flay back | FRANCISCO IVAN BASÍLIO - Ibiara - PB | |
PHILCO | 14CT6401 | Ripples at 110v | Altered waveform | Replace font scrs | paulo artur rio de janeiro |
PHILCO | PC 1427 U | Whistle when turned on, but inoperative | Power supply did not arm due to deficiency in filter component | Replace cap906,909,and diode905 | paulo artur rio de janeiro |
PHILCO | PCM 1448 | Turning off by itself | Dz 904 short | paulo artur rio de janeiro | |
PHILCO | TP 14U56 *** | No image check if there is power on the filament, when the screen increases it turns very faint white check if there is 180v in cap.c-713 if ok, note: rgb circuit must have 180v | Replace shock absorber | wagner | |
PHILCO | PCM 1443 EMOTION *** | Turning off white screen and retraces | R-715 c-719 | R-715 1r,subs 4r7 c-719 10mf x 350v | wagner |
PHILCO | TPF2130 | Does not turn on, without +14v pin 1 ic905 | Solda fria r931 18r 2w | BETO2828 | |
PHILCO | PCS 2078 NãO MARCA | Bu 2508 dx shorts out | C730 5k6 1kv6 changed and change original bu 2508 dx and increase c715 to 7k5*2kv | luiztvsom | |
TV PHILCO | PCM 2046 | Luminance- | Replaced the c716 10 / 250 volts | TV worked normally. | jaironuness |
PHILCO | TP-2053 | TV doesn't work std-by light blinks continuously but dimly | Changed the vertical output tda9309 | jaironuness |