PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | TPF-2140 | No sound just squeaking | C 401 smd em baixo do ic 101 | Replace or remove | Alvaro |
PHILCO | TP 1452 | No sound | Eprom, perhaps need for adjustments, vertical height | SYSTEM ELETRONICA JUNIOR | |
PHILCO | PCM 1446 | The TV turns on but does not obey commands, whether on the control or keyboard | Check r147 . r148 . r149 next to the keyboard | ze nascimento | |
TV PHILCO | PVT1014 | Image without blue in color | Changed the q- 806 | jaironuness | |
PHILCO | PCM- 1451 06 | Blinking LED does not turn on | C 911 and c 913 with low capacitance causing oscillation in the power supply secondary, i.e. +b and b5 varying | Replace c911 and c 913 tv ok | George Pontes |
PHILCO | 1443 | LED flashing.vertical closed.horizontal shrunken | Ic701 killing 9 volts that goes to pin 10 of 8361.8360 | Replace ic 701 | ANTONIO NOBREGA(patos.pb) |
PHILCO | PCM2146 CPH 05 | Inoperative, LED blinking | Replace d302 e micro tda8361 | Marcio | |
PHILCO | TPF2130 | Does not generate, when the power key is pressed the LED goes off and then lights up | Replace ic 903 tl 431 | ||
PHILCO | PCS-2976S | Image flickers on the sides | Replacement of capacitors c934 and c933 | francion | |
ITAUTEC PHILCO | TP-2052 | The LED only stayed on, and it didn't work. | R121- 1k ( aberto) | When turning on the device, it seemed that the power supply armed the LED stayed on but did not turn on the device, there is a lack of 8v voltage that powers the IC. oscillator o tda 8841 2y | spectroneletronica |
PHILCO | TP20V56 | The TV doesn't go into normal standby mode, but when you press the power key, the LED goes off as if it were going to start and nothing, only the LED keeps blinking | Lack of -12v voltage on the power supply secondary | D 909a shorted, r 912 and r 910 open. When replacing the TV it worked normally. obs d 909a specific trigger diode | GEORGE PONTES |
PHILCO | TP2053 | It takes time to turn on or does not turn on, all horizontal and power supply voltages are ok. | C715 (6n8 p/ 20" ou 5n6 p/ 14") | MACC | |
PHILCO | PT1453 | It turned on and then turned off and the LED just kept blinking, you would have to remove the socket from the mains to get the same symptom again. | Resistor (120 k 1%) in position 919 was open when replacing problem solved | Rivaldo | |
PHILCO | TP2054 | TV doesn't turn on but has 109v and doesn't oscillate horizontally | Short ci that regulates power supply but it was changed | adair | |
PHILCO HITACHI | PC1427U | Inoperable when turned on it just makes a noise and stops | Nao tem b+ def. flaybek | Help yourself leave your tip good luck ass: arni | ELETRONICA @RNI- LEOBERTO LEAL SC |
PHILCO | PCM2146 ... | Tv doesn't work | Blown fuse causes c-984 =4 nf 7, disc. | They were replaced and the TV worked beautifully. | Armando |
PHILCO REAL FLAT | TPF 2940 | Does not turn on, noise on the horizontal output board | D1701/by228 1500v shorted | Replace | Igor Almeida |
PHILCO | TP2054 | Bluish image with retraction lines. | Flyback | Adjust the screen | |
PHILCO | PCS 2952 | It worked normally, turned off after +or- 10 minutes, normal power supply. | Ic 601 ( la7833 ) saida vertical | I realized that IC 601 was getting very hot, I replaced it and the TV worked normally. | M&E ELETRONICA |
GRADIENTE PHILCO | TF2150 | Black screen on +-70% of the TV in the horizontal direction and on 30% of the TV it works normally with audio and everything | Enter service mode and reset which returns to normal | To enter service mode, simultaneously press menu on the remote control and on the TV with the TV turned on. | samuel leite |