PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14171
Results: 14171
PHILIPS Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS | GR2 | Sound but no picture | Check the lot cable for short circuit | ||
PHILIPS | 21PT166B/00 AA5 AB | No drive to lop transistor | Middle sections checked ok. carefully scoping the tda8361's hor. output showed gnd level to be at +0.8v not enough to drive next stage. change the tda8361 | ||
PHILIPS | GR2.2AA | Protection circuit operating intermittently | Diode 6592 was found to have leakage causing voltage to protection circuit to be too high, should be 23 - 28mv | ||
PHILIPS | ANUBIS A | Low contrast | C2448 47uf, 200v open circuit | ||
PHILIPS | 21PT5505/05 L9.1E | The fault with this tv was a snowy picture no channels tuned in also the permanent 33v supply on pin 9 of the tuner was low at only 1.6v | The first thing i tried was a resistance check between pin 9 and ground. the reading was only 120Ω. tsound's a surface mounted cap right next to pin 9 of the tuner. this was found to be leaky, it's value is 47nf. also resistor 3442 3.9k was o/c | ||
PHILIPS | 14PT1352/58 L6.1AA | Sound goes off and no remote control functions when heated | This was found to be due to a faulty micro | ||
PHILIPS | CTN-BB | Dead. f1500 o/c, mosfet s/c | Mosfet t7525 shorts, due to smoother cap c2505 goes low capacity. ic7514 tda4605 must also be replaced | ||
PHILIPS | 25PT532A/05 GR2.2 | Power supply dead, blowing fuse | Fault was transistor but124f 7625 short circuit, replaced transistor and also changed ic cnr50 7614 and tda8385 7600 this solved the problem | ||
PHILIPS | 25PT512A-05 GR2.2 | Dead set ht 140v ok | Replace standby thermistor thy6670 | ||
PHILIPS | L9.2E | Fuse 1572 blown | Disconnect pin 44 on ic7600, if the fuse stops blowing suspect processor ic7600. it is really expensive, at least in sweden ! | ||
PHILIPS | GR1AX GR1AX | Will not start up from cold | Check if 95v line increases to over 100v when tr7628 bf423 is chilled. if so, replace d6629 bzx79-c12 and re-check 95v/re-adjust r3625. may also be worthwhile replacing tr7628 and c2629 as a precaution!! | ||
PHILIPS | GR2.4AA | Power supply protection enabled | Replaced zener diode 6561 bzx79c68 | ||
PHILIPS | VR110 | Power supply tripping | Damaged print at one of the pins on primary side of transformer | ||
PHILIPS | L6.2 | Picture is horizontally narrowed and deformed | Capacitor c2913 390nf, 250v on the deflector pcb had lost capacity | ||
PHILIPS | 28ML8805-16B FL1.6AA | Power supply faults. bux85f in micro sops defective | Change the value of c2260 to 4n7f, replace 7270 with transistor bd825 | ||
PHILIPS | 28ML8805-16B FL1.6AA | Ticking noise and line in picture | Transistor 7381 bc848c defective when hot | ||
PHILIPS | 28ML8805-16B FL1.6AA | Disturbed sound in left channel | Check ic7009 lm833 on lsp | ||
PHILIPS | 2B 2B | Very low ht voltage | The ht was so low that a 60w lamp connected across the ht line as a dummy load wouldn't even slightly glow. the problem was caused by a wrongly fitted ptc, it was a 96012 type, when the right ptc 96012 was fitted the problem was solved | ||
PHILIPS | 28PT4521/16 MD1.1E | Fails to stop at station when tuning | R3568 100kΩat side of l10 connector | ||
PHILIPS | 28PW6322-05 MD1.2E AA | No picture and no sound and when switching on, the high voltage transformer makes a sound | The capacitor in pos. 2420 was bad it produced smoke after some time |