PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14171
Results: 14171
PHILIPS Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS | 14PV182 COMBI | Dead with tape stuck in machine | Loptx | ||
PHILIPS | 14PV182 | Tripping on & off at 1 sec intervals | Mc4403 chip ic7130 in psu | ||
PHILIPS | 14PV182 | St/by only with vcr shuffling constantly | Loptx - had hole in it | ||
PHILIPS | 14PV182 | No r/c operation | Ir pickup module has no o/p although its supply is correct - replace part no 4822-218-11745 | ||
PHILIPS | 14PV182 | No r/c operation | Replace i.r pickup unit on vcr front pcb part 4822-218-11745 (seme) £3.44 | ||
PHILIPS | 14PV182 | Dead, tripping | T7583 but12af s/c on main pcb | ||
PHILIPS | 14PV172 | Start up problems after replacing ts7352 | When ts7352 is replaced, it can happen that the set doesn't start up properly. there are 2 possible solutions for this problem: - use sgs type mtp3055e (4822 130 63726). - in case of a motorola type mtp3055v (4822 130 60838), add a 22 uh coil soldered | ||
PHILIPS | 14PV172 | Start up problems | When the set is switched on by the mains-switch while a cassette is in the set, the front led starts blinking, but the set doesn't start. solution: check the primary voltage (ubat) and adjust this for 14" sets to exactly 101.5 volt. (see chapter 3.1.1 | ||
PHILIPS | 14PV172 | Spare part information | If the lever inside the mains-switch is broken, the switch doesn't remain in the "on" position. solution: replace the switch by a new one. improved switches of a newer production range are on stock. (4822 276 13542) | ||
PHILIPS | 14PV172 | Modification | From production week 9725, the ic's sda5649, sda5649x and sda5648 are replaced by a sda5650 (4822 209 15504). this new ic is fully compatible with the others, but has better characteristics. in addition to this modification, r3812 on the small signal bo | ||
PHILIPS | 14PV172 | Memory erase procedure | The contents of the memory can only be cleared via the service mode. this option is not available for end users. (risc of destroying option codes). service mode: press "stop" on remote control and "play" on the set for 5 seconds. select the second page | ||
PHILIPS | 14PV172 | Key set | The key set assy has been codified for all b-range tvcr's. this will allow to change the keys without having to change the complete frame. servicenr. 4822 410 11075 - key set for: 14pv263/01/02/08/13 - 14pv264/39 - 14pv163/05 - 14pv172/01/05/08/13/39 - | ||
PHILIPS | 14PV172 | Code number correction for deck-up (ic 7410) | The codenumber for the deckprocessor was wrong in the first service manual (4822 726 15451). in service information tvcr96-01 and in the new manual the correct codenumber is given. the codenumber for the deck-up for sets with non-turbo drive is: 4822 20 | ||
PHILIPS | 14PV172 | Calling installation menu | The installation menu is activated by the following procedure: - switch on the set by means of the stop key. - press simutaneously the "stop" key and the "volume -" key on the set. | ||
PHILIPS | 14PV170/05 | To select tuning mode | Press "stop" & "vol-" together on set to eneter tuning | ||
PHILIPS | 14PV170/05 | No pic & tape stuck with mechs pulsing & led flashing | Dis lop stage got mechs working - loptx faulty | ||
PHILIPS | 14PV170/05 | Deck shuffles at sw on , st/by led goes out then repeats | Loptx faulty | ||
PHILIPS | 14PV170 | Osd missing | Replaced faulty 7.5mhz coil 1802 on main video p.c.b. ( no osc. on pins 42 and 43 of i.c. 7801 was the clue ) philips part no. 4822 157 712 89 | ||
PHILIPS | 14PV170 | Key set | The key set assy has been codified for all b-range tvcr's. this will allow to change the keys without having to change the complete frame. servicenr. 4822 410 11069 - key set for: 14pv162/01/02/05/07/08/13/58 - 14pv170/05 - 14tvcr240/01n. | ||
PHILIPS | 14PV164/05 | Dead with lop tr s/c | Line dr w/frm low amplitude to loptr due to leaky tr7205 bc848b |