PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14171
Results: 14171
PHILIPS Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILIPS | 14PV263 | How to activate/de-activate "hotel mode" | Activation: - set volume to desired level. - select programm 38. - press the stop button of the remote control and the stop button of the vcr for about 5 seconds, until the message h+ appears. de-activation: - set volume to desired level. - select p | ||
PHILIPS | 14PV263 | Correction service manual 14pv263/01 | The indication of the small-signal pcb (page 1-3) is wrong. the right indication is psspp3/gpvxf. this pcb is only applied in 14pv263/01. | ||
PHILIPS | 14PV263 | Codenumber information | Please add following codenumbers to the service manual: lift-flap 14pv263/01 : 4822 443 10404 lift-flap 14pv263/02 : 4822 443 10404 spring for lift-flap : 4822 492 70896 | ||
PHILIPS | 14PV263 | Codenumber information | The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702. | ||
PHILIPS | 14PV263 | Codenumber correction | The codenumber for the scanner-motor (pos. 34) in the service manual is wrong. the correct codenumber is 4822 361 215 48. | ||
PHILIPS | 14PV263 | Codenumber correction | The codenumber of pos. 1701 (tuner) for 14 inch sets with iec input is 4822 210 10691 (uv916s). | ||
PHILIPS | 14PV263 | Calling installation menu | The installation menu is activated by the following procedure: - switch on the set by means of the stop key. - press simutaneously the cursor left and the cursor right key on the remote control. | ||
PHILIPS | 14PV210 | No pic; r3199 burnt | R3199 (9k2) and d6183 (smd) used 1n4148 in lieu | ||
PHILIPS | 14PV210 | Fault codes | Record led flashing >>>error in eeprom1[ic7818]; timer led flashing>>> error in eeprom2[ic7801]; stdby led flashing>>> error in textmicro[ic7804] | ||
PHILIPS | 14PV202/07 | Int blows fuse at sw on | Replace degauss coil, degauss posistor and 1.25 amp fuse | ||
PHILIPS | 14PV200/07 | Dead apart from popping sound at sw on | D6391 byw98 200 rated at 3a s/c - used by399 in lieu | ||
PHILIPS | 14PV200/07 | "n act" shows at sw on | Switch the combi off with the mains switch. depress and hold both the wind & rew buttons on the combi while switching back on (keeping the buttons pressed for around 5 seconds) release the buttons and this should clear the memory and allow the combi to be setup as normal | ||
PHILIPS | 14PV184 | Reverts to st/by at sw on aft loptx replacement (led goes from brief green to red) | Eventually comes on with dull grey raster. prot line on micro ic7801 pin 53 vcr pcb only 1v (5v) - check at d6568 lh plug 1923 - prot tr 7550 bc547 leaky (front left edge of tv pcb) | ||
PHILIPS | 14PV184 | Menus not displayed | L1802 on bottom panel across pins 42 & 43 of micro ic7801 | ||
PHILIPS | 14PV183ETC | Service mode adjustments | Press "stop" on handset & "play" on keyboard together for 5 seconds | ||
PHILIPS | 14PV183ETC | No chan +/- on r/c after eeprom replacement | Enter service mode & set correct option number - to be found on back plate of set | ||
PHILIPS | 14PV183ETC | Hotel mode activate/deactivate | Press "stop" on handset & "stop" on keyboard together for 5 seconds while on channel 38 | ||
PHILIPS | 14PV183 | To enter service mode | Press "stop" on r/c & "play" on keyboard for 5 seconds | ||
PHILIPS | 14PV183 | To activate/deactivate "hotel mode" | Press "stop" on r/c & "stop" on keyboard for 5 seconds while on ch 38 | ||
PHILIPS | 14PV182/05 | Osd missing | L802 7.4mhz osc coil o/c pt no 4822 157 71289 |