Search: PHILIPS
Results: 14169

PHILIPS Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PHILIPS29PT 554
Vertical thick linesSwitch (r-3410 and r-3411) are connected in parallel with the deflectorAdemar / Videira sc
PHILIPS20PT 222
Closing the image from left to right.Change diodes d6461 / d-6464 (1n4148) change c-2469 (390pf) c-2462 (4k7) the capacitors are 2kvAdemar / Videira sc
PHILIPS29PT 552
Sem +b not secondaryCheck the capacitor (c-2550) which is connected in parallel with the d-6550Ademar / Videira sc
PHILIPSTODOS LINHA PT
Turns on, after a while it makes noise on the screen,Replace the (c-2472 of 150k) replace the (c-2473 of 100k) and the horizontal output transistor bu-4508/dxAdemar / Videira sc
PHILIPS29PT 5645
L-4U
Tsound is no +b in secondary schoolCheck and replace ci tea 1620 of the power supply replace capacitor smd c 2532 and resistor r 2513 (2k2)Ademar / Videira sc
PHILIPSTODOS LINHA PT
Sreem adjustments in inches(14p 340volts) (20p 420volts) (21p 450volts) ( 25p 480volts) (29p 520volts)Ademar / Videira sc
PHILIPS20PT 3331
Turns off after approximately 5 minutesChanging the q-7643 bc 546 can use the bc 547Ademar / Videira sc
PHILIPS20PT220
Sem osdReplace q-7682Ademar / Videira sc
PHILIPSVARIOS
Image shifted to the rightReplace( c-2448) ( c-2255) ( r-3242) ( r-3469) ( r-3490) ( d-6449) e (d-6468)Ademar / Videira sc
PHILIPS20PT 3336
No image, just charactersSwap r-3442 and r 3459 is close to the fly backAdemar / Videira sc
PHILIPS3331
Reduced frame and power supply with 68 volts on the secondaryChange the r 3526 without testing the value of 0.15r connected to the fetAdemar / Videira sc
PHILIPS1340
Green screen with linesTouch zener diode (zd 359) 3.9 voltsAdemar / Videira sc
PHILIPSCHASSIS L-04
L-04
Turns off with error 11Change coupler photoAdemar / Videira sc
PHILIPSTODA LINHA GR-1
Jagged imageReplace r-3226 (18k)Ademar / Videira sc
PHILIPS29PT4635
After 5 minutes the video disappears and tsound are only characters, also on the av.Replace ic 7200 o micro.Henderson(hndrsn)
PHILIPS14PT3336/78
TV with broken board, restoration was done and the TV started working again, but kept turning offSolution: adjust the screen. and the TV was ok.Carlos
PHILIPS23PFL5522D/12
LC72ELB
Does not turn on, LED of, power supply vibratesNa power supply d205 (sb360 ,3amp 60v)Replace c24 (331k/3kv)J.CUNHA
PHILIPSFWM57
Damaged by lightning (dead)After a lightning strike, he was dead, with the display completely turned off. On the power supply board I found inductor 5929 open, whose value indication in the diagram is 1m. as inductor 5931 also has the same value, I measured its resistance and found 12Ω. So I added three identical inductors (from a piece of scrap) which together gave almost this much, I replaced them and the device was perfect. In the open inductor I could notice that the wire was extremely thin and despite it being in series with the 200 ma fuse 9902, it will certainly always open before the fuse, in case of overload.littlecarlos
PHILIPS29PT4635/78
Dead power supply does not turn on standby LED does not have +b 140v +b12vCapacitor 2521 22mf 50vReplace with newbrancobilli
PHILIPS20PT4331
L03.1L
It turned off after 5 seconds. error 11 in service modeResistor 3443 (3r9) resistor 3444 (4r7), resistor 3403 (340r) overheated and alteredReplace for another of the same respective valuedjeferson hoed