Panasonic TV Repair: Common Faults and Solutions.
Search: Panasonic
Results: 2880
Results: 2880
Panasonic Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PANASONIC | EURO 7 TX-68P200A | Faulty colour on rgb | Ic1315 | ||
| PANASONIC | EURO 7 TX-68P200A | Failed tint | Q1340 | ||
| PANASONIC | EURO 7 TX-68P200A | Failed sub colour | Q1477 | ||
| PANASONIC | EURO 7 TX-68P200A | Failed sub bright,pink picture | Ic1315, d010 | ||
| PANASONIC | EURO 7 TX-68P200A | Failed aft | Tnr001 | ||
| PANASONIC | EURO 7 TX-68P200A | Dead | D20, r874 | ||
| PANASONIC | EURO 7 TX-68P200A | Bright picture | D354 | ||
| PANASONIC | EURO 7 TX-68P200A | Blue pix teletext | Ic1315 | ||
| PANASONIC | EURO 7 TX-68P200A | Av picture shifted to left | Ic1104 | ||
| PANASONIC | EURO 7 TX32PG30 | St/by only | Reset line volts going into u1 pcb stuck halfway - being loaded by faulty sm filter lc1118 in reset line | ||
| PANASONIC | EURO 7 TX28MDMK1C/M | White raster , no osd - sometimes g with fb lines - very int | Replaced micro sda5450c48 (34 ukp) | ||
| PANASONIC | EURO 5L TX36PF10 | Tries to start up but shuts down into standby within seconds of pressing the power switch. | Replace the 2sc2925sta line driver transistor (q502) which had an open circuit b-e junction and also replace the x24c0501ua earom chip (ic1102) which had become corrupted. | ||
| PANASONIC | EURO 5 TX33PF10 | Sound but no pic | Perform 'self check' by pressing "-/v" button on set & "status" button on handset together. to exit switch off with power button | ||
| PANASONIC | EURO 5 TX33PF10 | Low unadjustable sound on av | Perform 'self check' by pressing "-/v" button on set & "status" button on handset together. to exit switch off with power button | ||
| PANASONIC | EURO 5 TX33AK10 | Watery, pixellated pic with after trace on movement | Eeprom corrupt - to reset hold vol- on set & status key on r/c together with set on. goes thro' its routine then needs retuning etc. | ||
| PANASONIC | EURO 4Z CT2153STX | Dead with q551 loptr s/c | Fit repair kit tzs9ek001 | ||
| PANASONIC | EURO 4Z | Dead | The standby transistor q951(2sc4004) s/c, it's emitter resistor r954(6r8), d958 (1n4148) s/c, and r975 (270r 1/2w fusible) o/c all in the standby circuit, would go up in a cloud of smoke repeatedly until i... eventually, located the culprit r964 (82r 1/8w) which had risen in value to approximately 260Ω. it feeds d953 a 12v zener in the feedback circuit. | ||
| PANASONIC | EURO 4 TXW28R4DP | Attempts to start with a burst of eht but reverts to stby | Replace d558 1sr124-4at82 s/c use byd33m & r559 r33 safety in supply to fop ic. replaced loptr with beefed up one from pan & resoldered line driver tx & dry joints in lopstage. | ||
| PANASONIC | EURO 4 TX32PK2C | No rear surr sound | Ic2704 tda2030av overheated: ok aft replacement | ||
| PANASONIC | EURO 4 TX28PK2 | Trips with relay chattering after few mins | In overvolts mode - 150v ht gone high due to r872 dry joint |