Search: Panasonic
Results: 2880

Panasonic Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PANASONICMX-D830
Turns on, with all normal voltages, but tsound is no soundMemory locked due to some error in the deviceReset memory mic4 25l1006. temporarily short circuit pin 8 of the 3.3v to gnd while turning on the device. When the device starts up completely, remove the short circuit.Jump Eletrônica
PANASONICTH-42PV80LB
GPH11DA
TV does not turn on, red LED flashes once.Cold solder on the bga microprocessors on the main board a.Resoldering of bga microprocessors position ic8001 and ic9901Rafael do Carmo
PANASONICTC-14RM12L
When turned on, it works for a few seconds and turns off, with the LED blinking.Defective protection circuit.After measuring all the voltages and they were all ok, the solution was to turn off the protection circuit (remove r1106) and the device worked normally.Francisco Oliveira
PANASONICTC-L32B6B
With normal sound without image backlight onT-com boardJanilson JD ELETRONICA CAETITÉ-BA
PANASONICSA-AKX50
Turns on in a few seconds turns offThe cause was a high power supply that caused the short in the audio output, I found the ic5799 - mip2f2 leaking in the power supply and the transistor q5720 - ktd863y, I tested it, it was leaking a lot, I replaced it with new ones, the power supply came back with normal tension and in the audio output I replaced the ic5400 and ic5000 - tda8950j both are shorted, I also found swollen and exhausted electrolytic capacitors c5510,c5511,c5512,c5513 - 220uf 50v and c5440,c5040 - 22uf 100vI replaced all these components and the Panasonic sound was ok.Eletrônica Dolby
PANASONIC29KL03
No contrastWas replaced r557,res.95k3 open.José delta line
PANASONICTC20A12
Works - frame reduced to top with flickering imageCi 451Replace ci 451-vertical-an5539=la7840EMERSON RIBEIRO
PANASONICSA-AK220
When you press power, f61 appears on the display and then turns off.Sound output (rsn35h2b) and cold soldering on almost the entire amplifier board.Changing the output and resoldering the amplifier board.Liani Belles
PANASONICL24X5B
Blinking LED doesn't turn onC1110 c1114 orange capacitors replace without measuringMega Center
PANASONICTV14A12
Vertical position would suddenly stretch a little and the TV would turn off and blink on standbyC519 open (it is close to the fly-back on the +b line)naldo
PANASONICTC-20A9
TNP4G076
Blurry image when switching on. After a few minutes on, the image was normal.It was leaking high voltage from the focus wire at the flyback output. the focus wire was loose from inside the flyback and was oxidized.Flyback replace.Rafael Silveira
PANASONICTC14A8
Does not turn on with normal power supplyFaulty ic 101Replaced and got fileleilson lagoa de roça pb
PANASONICTC20A10
Vertical opening only 4cm in the center of the screenResistor r425 27k abertoReplace of the samemateuspagnan
PANASONICTC20A8
No contrastR564 100kReplace and go to the crowdMega Center
PANASONIC29KL 04
Burning q753Tvc had output h and q 753 burned out, after the change the tvc kept burning q753Replacing the d 556 rh 3g diode - problem solvedzapeletronica
PANASONICTC-29KL05
The relay would hit and go into protection mode, it wouldn't turn onD556 shortedI replaced d556, q753, r768, c757, c563, r520 and r521 the defect was resolved thanks to this forum I will share it with youThis email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONICTC-32X30B
Green LED flashes several times and then the red LED flashes 3 times and does not turn onI released the cable that takes the signal to the display on the side of the main board, the TV turned on the screen. I reconnected the cable to the main board again and the defect returned. Even so, I left it connected and disconnected it from the display side and the defect persisted. I even thought the defect was in the cable. lI cleaned the side of the cable connected to the main board using an eraser like we do on computer memories and applied contact cleaner to the main board connection, and the TV started working normally again.jfr
PANASONICTC-20C5
Almost completely closed verticalR455 openjpsky
PANASONICTC20C5
No sound and no image with horizontal output transistor shorted q501When replacing the horizontal output transistor q501 burns out immediately.In my case I had to replace q501(2sd1632), c511(peak capacitor) 8200pf and also the flyback(tlf15564) simultaneously as they were all burnt out. It is good to check all capacitors and diodes of the horizontal output and also the 180v line and finally check the +b 140volts.Otacilio
PANASONICTC12A14
Acting protectionDisconnect pin 36 of the microBruno nicacio