Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4758
Results: 4758
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PC2041 | Turning off after flyback replacement | Resistor r723 (27k) open abl line | ARAUJO | |
| PHILCO | TP2052 | It doesn't turn on, or it oscillates and turns off and the LED keeps flashing | C706 6n8 leaking capacitor | I put another one it worked perfectly | FRANCISCO RS |
| PHILCO | TP2053N | Blinking LED doesn't turn on | Shorted deflector coil | Replace the coil | francisco rs |
| PHILCO | PC2013U CPH02 | Vertical closed | Capacitotor c 611 de 100uf/100v rim | Also replace c607 at 10μF/63v and c609 at 4.7μF/63v | francisco rs |
| PHILCO | PCM2146 | Inoperative, stand-by LED flashes and does not turn on | Capacitor c905, replace as it is open | claudio e reinaldo | |
| PHILCO | TP-2054 = TP-2053 | It doesn't turn on when the standby LED starts blinking +b at 109v it drops to 15v @@@ | Saida vertical tda9309 tv tp-2053 a tv tp-2054 vertical tda9302 a ou h | Help yourself, leave your tip ass.arni | ELETRONICA ARNI-LEOBERTO LEAL-SC |
| PHILCO | TP-2054 = TP-2053 | Does not turn on when turned on, the standby LED flashes | D09, R10=47.0, R12=47.0 | ELETRONICA ARNI-LEOBERTO LEAL-SC | |
| PHILCO | TP-2054 | E.a doesn't turn on LED keeps flashing @@@@ | D09, R10=47.0, R12=47.0 | Help yourself, leave your tip ass.arni | ELETRONICA ARNI-LEOBERTO LEAL-SC |
| PHILCO | TP20V56 CP02R0 | Doesn't start | D909 in the power supply secondary | luiz g.silva | |
| PHILCO | TP20V56 CP02R0 | Doesn't start | Power supply secondary d900 | luiz g.silva | |
| PHILCO | PCM2044 | Verticalopen only 5cm from the middle upwards | C-613 pin 3 of vert output. 2n2 was with 1n6 | joaoxx | |
| PHILCO | TP-2052N | Does not turn on, LED off, device inoperative without voltage on the power supply secondary. | Cold welding at the power supply. | Resolder r910, r909, d906 and points on the same power supply line. | celinvds |
| PHILCO | TP1410 | Standby is on but when I turn it on it starts blinking but doesn't oscillate the TV only has +b 106 volts | 15 homs resistor burnt or with raw solder check it position r931 and it feeds the 1000mf x 16 volt capacitor take advantage and change it without testing the c918 | ||
| PHILCO | TFP2902 | Horizontal shifted right side | Capacitor c732 smd 2n2 | ||
| PHILCO | PCM 2044 05 | Vertical closed dark strip at the bottom | Capacitor 1000uf35v no esquema c610 | I replaced it, it was a jewel | dgspeg |
| PHILCO | PCM2044 05 | Vertical closed dark strip at the bottom | Capacitor 1000uf35v | I replaced it, it was a jewel | dgspeg |
| PHILCO | PCS-2956 CPO1LR01 | TV with no image and no sound; with line of retraces. | Irregularities in the ic101 (m37274ma), memory, blocked the system when activating the image adjustment in the menu. | After replacing the ic 101 (m37274ma), the device was ok. | clayton |
| TV PHILCO | PCM 2044 | Blinking led | Takes about 20 minutes to work | Solution capacitor c722 470μFx25v, replaced and resolved. | BF.COLATINO |
| TV PHILCO | 20V56 | With drizzle. | None of the channels worked, before condemning the seletronic I checked that it had 33v and the appropriate voltages, but when checking the date and clock line I saw that there was no clock signal. | Following the seletronic backwards I saw that r202 100r smd version was open. because there was a sign on one side and not on the other. I replaced it and that's it. all channels are working again | BF.COLATINO |
| TV PHILCO | PCM-2046 | Doesn't start | After finding that the c716, r706 were broken and replaced | I checked that the flayback was shorted and I replaced the components and everything went back to normal. | BF.COLATINO |