Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4811
Results: 4811
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PH39N86DSGW | Faded screen with LEDs ok only no | I tested the LEDs and all ok anyway did not light, LEDs with altered resistance replace even being lighting | Uti das tvs e microondas | |
| PHILCO | PTV32G23AGSSBLH Ver. A | Do not turn on, only Standby lit. | Short circuit in the C3P47 SMD capacitor next to CI U0P1 | replace capacitor valor 100x16v | rafaelmoraes99 |
| PHILCO | PCS1600 | Intermittent audio, sometimes sound comes out and sometimes not. | Mute circuit review. | Eduardo Costa. B.F Eletrônicos. EA Revendas | |
| PHILCO | PH29E63D | I am sound. | In my case, it was software update. | Vilian Costa | |
| PHILCO | PH32E53SG | Purple or bluish picture | Old leds | LED bars | Darci Denzer |
| PHILCO | PH55A17 | Don't call, don't light up | Micro cold loose | RESOLDAR MICRO | JL ELETRONICA SR |
| PHILCO | PH39N91DSGW Ver. B | Main | replace main, everything is the same as | Use PH32B51DSGW A Version | Eletrônica Silva Homs |
| PHILCO | PH55A17DSGWA VERSÃO C | doesn't start, just get Standby lit. | Short circuit in the 3V3 line of the main plate, measuring short on the L3D1 coil near the processor. | Defect was the CI U3 oscillator of the 3V3 power supply that was short. I used a similar CI taken from scrap and worked perfectly. | rafaelmoraes99 |
| PHILCO | PCX5501N | PCX5501N all and turn off Off | EEPROM CORRUPPE | NEUPSX4 | |
| PHILCO | PH32B28DSGW | Restart | Update | Download the file to Philco, put it on the TV USB, press the pawer key and hold, put it in the plug and wait for it recognizes the update. | Cabeça |
| PHILCO | PH55M LED SMAT 3D | The TV called and learned the Philco logo then turned off the screen == This TV and the one that has two 83 LEDs regies each. | It was 129v in the exit of the LEDs to the screen. | I removed from the plate inverting the following 3.6Ω resistors in parallel r34 and r65 + r35 and r67 + r38 and r71 and put in the lamp of each resistors of 4.7Ω the voltage went to 122V and went back to work ok | Max Matipó |
| PHILCO | PH32N62D | TV without Standbay, has no secondary voltage, zener brand*(EA2) which is a short LT431 next to photoacoplator and CI PWM Burned | these components were replaced and was solved | Rodricell | |
| PHILCO | PH32N62D | tv ph32n62d sem backlight | TV PH32N62D without backlight, only 30V arrives, glue under the r35 resistor of the power supply with bad contact | Rodricell | |
| PHILCO | PH21M SS | turn on then turned off | capacitor c803 fault | Just replace the 220UF400V capacitor | Mvp Assistec |
| PHILCO | PTV40E21DSWNC LED | When replacing LEDs and reducing chain, TV always turns on the first one by giving 53V, turning off in the control and turning again, rises to 63V (ideal). | In the 1k R2B9 resistor scheme, but comes with 10k, replace with 100k | replace resistance r2b9 or remove, device went back to work perfectly | Beto , eletrônica box 4 |
| PHILCO | PB500BT | Sound works and shuts down | Works and off | ||
| PHILCO | TV PTV49F68DSGWN | Backlight lit and without picture | In my case it was C216 with escape on the V.Con plate | Just take the capacitor and run to hug | jorge assistencia tecnica cotia sp |
| PHILCO | PH51U20 DSGW Plasma | TV Liga appears the logo and turns off | replace both 450x 100 C412 and C413 capacitors | ||
| PHILCO | PH24M LED A 40-00MS09-MAC2XG | Don't tune channels | Regulador u804 5v as1117 smd | replace the regulator and run to hug in some cases the update solves tb | Rafael Sena |
| PHILCO ATUALIZAçãO | PHILCO ATUALIZAçãO philco atualização | Philco Update | Philco Update | NEUPSX4 |