SAMSUNG TV Repair: Common Faults and Solutions.
Search: SAMSUNG
Results: 3754
Results: 3754
SAMSUNG Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG | MAX A66 | Protected message when connecting. | Cleaning the CN2 and CN3 connectors. | amsinformatica | |
| SAMSUNG | LN32A550 | Bad image, inverted colors, sometimes no image | Cabo lvds | Disassemble the terminals and clean, or replace them! | Rodrigo cofferi |
| SAMSUNG | UE40F6200AK BN44-00616A | Doesn't work, qp801s burnt out | Fp801s(5a), qp801cs(13nm60c), rp811(0,47ω), rp810(100ω), rp813(20ω), dp801(bav70t), icp801(sem3050), dp808c(sf38g), cp812(22µf/50v) | Andrew | |
| SAMSUNG | CL21K40MQ KS9C | Turn on is to turn off quickly with a very loud chirp on the flyback | Shortened deflector all black inside | I put another good one it was good again | Algustinho eletrônico |
| SAMSUNG | CL-21Z43MQ | Turns on with sound and no image, low power supply. | Tl431 regulator | Pardal - X | |
| SAMSUNG | LN40J5200 | Just backlight on with sound no image | On the main PCI close to the power supply connector f202, on the v-con fp1= 3a, shorted cp30 next to cp31 close to the up1 ci | Measure the v-con fuse, if it is bad, replace the components mentioned | NEI |
| SAMSUNG | T22B300LB | Doesn't start. 3v3 is missing, which comes from +5v, it has a weak 1.2v. | Ic 202 it is a 3v3 regulator, 1g1 = subs 78l33 philips, the 1g1u pin1 ground, 2pino2 input 5v+, p3 output3v3 | Place the 78l33 philips pin 1 output 3v3, pin2 ground, pin3 input 5v+ | guinga sdia goias |
| SAMSUNG | UN48J5200AG | Varying colors on the screen blue, green, red. | In my case, I just changed the t con. | Luciano | |
| SAMSUNG | UN48H4200 | Turns on, tsound is sound, turns on the LEDs and tsound is no image. It doesn't have the 12 v that powers the screen. | On the main board, q201=(1e) open. It is next to resistors r808, r242 and r241. good luck!!! | JOÃO CARLOS ELETRÔNICA | |
| SAMSUNG | PSPF411701A BN44-00161A | Doesn't work, lacks +5v stdby ccts | Check swap: f801s, fb801, icb802, db810, db811, db812, zdb804, db806, db807, cb813 | Andrew | |
| SAMSUNG | PS42Q97HDXXEU PS42C91HXXEC BN44-00204A DYP-42W3 | Does not work, fault in qs801 and qs802 | Check swap: f801s, fm801s, qs801, qs802, ds804, ds803, rs814, rs812, ics801 | Andrew | |
| SAMSUNG | PS42Q97HDXXEU BN44-00159A DYP-42W2 | Does not work, fault in qx801 and qx802 | Check swap: f801s, fx801s, qx801, qx802, dx803, dx804, rx813, rx815, icx801 | Andrew | |
| SAMSUNG | PS42Q97HDXXEU BN44-00159A | Does not work, fault in qs801 and qs802 | Check swap: f801s, fs801s, qs801, qs802, ds803, ds804, rs812, rs814, ics801 | Andrew | |
| SAMSUNG | RBPS42B450 PS42B451 BN44-00273D | Does not work, qs801 and qs802 | Check swap: f801s, qs801, qs802, rs816, rs814, ds803, ds804, ic801s, nt801s | Andrew | |
| SAMSUNG | UE58J5200 BN44-00787A L58GFB_ESM REV 1.2 | Backlight blinking or inoperative, no output voltages, q9101 and q9102 burned out | Check/replace Q9101, Q9102(AOD9N40), IC9101 (SEM5027A) | Andrew | |
| SAMSUNG | BN44-00787A L58GFB_ESM REV 1.2 | Does not work, qp801cs failure, pfc cct failure | Replace verificar: fp801s (5a), nt811s(ntc5d15), rp801, rp802, dp801, dp808c, icp801 | Andrew | |
| SAMSUNG | BN44-00787A L58GFB_ESM REV 1.2 | Does not work, no output voltages | Replace verificar: fp801s (5a), nt811s(ntc5d15), qm801cs(50r380p), qm802cs(50r380p), rm813, rm815 (22ω), rm814, rm816(100ω), dm805, dm806(bav70), icm801(fa6a20n) | Andrew | |
| SAMSUNG | LN40C530F1M | TV turns on but the backlight lamps do not turn on. | Rust on plate r1848 r1875. | Replace resistores r1848 ( oid smd 100k ), r1875 ( oid smd 100k ) | RNSPTEC |
| SAMSUNG | UN46F6400 AG | Turn on then turn off | Relay keeps knocking | Replace ci sl 2013m power supply board | Tec center |
| SAMSUNG | CL29C650GQ | I'm sound | 5.6k r625 open or shorted | Eletrônica Mauro Mascarenha - Parazinho Ceara - Tel : (88)981422821 |