SAMSUNG TV Repair: Common Faults and Solutions.
Search: SAMSUNG
Results: 3754
Results: 3754
SAMSUNG Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SAMSUNG | 43F4000 | After 5 minutes the TV turns off | Cracked solders on the power supply board | Cracked solder capacitor cs809 | RMSELETRONICA |
| SAMSUNG | LN32C530F1M | LED blinks but nothing turns on | Main plate rebarg take the plate to the 100craus electric oven for 20 minutes | FRANCISCO FERREIRA | |
| SAMSUNG | BN44-00622A-D | Pfc does not start | Rs802 (10r) open | Pablo | |
| SAMSUNG | CL-21Z50MQ | No audio | L201 open | Adriano eletrônica | |
| SAMSUNG | LT28D310LH | Screen flashing like LED bars | Power supply board defect | Replace the board | Mariano |
| SAMSUNG | T27A550 | Turning off by itself LED flashes 2 times quickly | Cold solder SMD STBY resistor from the power supply, ground the STBY pin | Rsf | GIOVANO ELETRONICA |
| SAMSUNG | UN49J5200 | Does not turn on, standby blinking. | Screen defect. | It may be in the fat that goes to the right or left screen, it will be necessary to calm down in the analysis, isolating 12 by 12 from the left fat, from left to right until it is resolved. | Antony Garcez |
| SAMSUNG | UN55UK6000 | No image, TV flashes stand by and does not turn on. | Screen defect. | Isolate 14 lanes in the Fiat to the right of the technician going to the screen, from right to left from lane 13. | Antony Garcez |
| SAMSUNG | LCD, PLASMA, LED | Remote control leaking one of the batteries, even though it is new, alkaline, in less than 6 months it rusts in the same spot and leaks | Short circuit of the battery terminals with the printout corroded by the acidic battery fluid | Clean well, polish the terminals with steel wool, wash the board, and after drying, insulate the back of the board with durex or insulating material. | Trendset |
| SAMSUNG | LN32C530F1M | Does not turn on_ stby on (pci main inoperative) | C279 shorted killing 3v3 | Replace to electrolytic 10μF x 10v. | duc40rj |
| SAMSUNG | PL64F8500AGXZD | No image | I used the tip from Centertec Suzano, it worked, it was just the 3 blue caps, I replaced them and it worked. thanks | Replace 3 10μF polyester cap | Eduardo tomas silva |
| SAMSUNG | UN32J4000AG | Does not turn on the backlight, LEDs (back light). however, turning on and acting channels and volume. | After a long time, thinking that it could be the LEDs and the main board, we discovered that it was simply the socket (white) that connects the main board with the LEDs, changing it solved the problem | Eletronica União | |
| SAMSUNG | UE65MU6102K | After turning on, it goes out immediately, leaving the LED flashing. | Fuse f223_ut open and c456_ut shorted on the main board | jose almeida tavares | |
| SAMSUNG | T22C310LB | TV doesn't turn on, LED doesn't light up | Ic1601 torrado | After searching the net, because the c.i. it was toast without numbers; I discovered that it is a tps54328. | Alexandre Oliveira |
| SAMSUNG | 29Z50MQ | When turned on, the relay triggers, the LED blinks, does not oxidize and the power supply rises to 150v. | My robe is stuck | Close to the micro. | ELTON CASTRO (eletronica nova era .cabo pe) |
| SAMSUNG | LT27B350 | Sometimes it works, sometimes it doesn't. Sometimes it turns on and off, shows the logo and turns off. The LED blinks twice five times. | See q202, transistor (marking "1e"), which is on the signal board, close to the socket that comes from the power supply | Replace of the same | arock |
| SAMSUNG | BN44-00259A BN44-00262A BN44-00260A BN44-00289B BN44-00261A BN44-00291A | No power to backlight caused by diode on ip board. | Change dp805 (from mur360 to 31gf6) diode (rectifier 600v 3a) on ip board. | SEUK Technical Support | |
| SAMSUNG | P 2270 HN | TV turns on with normal audio, no image, appears to be defective in the LEDs. | T 301, inverter transformer (tm 09180) with one of the output coils broken, you have to take it out and measure, 1.4k, depending on the code, it has to have the same value. | Changing the inverter transformer. | Geraldo de Petrópolis |
| SAMSUNG | UN40H5100 | Stuck on the samsung logo, then the logo changes color giving the impression that it IS the screen | Change nand memory | MARIANO | |
| SAMSUNG | LN26B450 | Doesn't start. | No voltage in the secondary. identified burned fuse FM802 (amp) and also IC (ice3br0665j) short signals on pin 4 with considerable damage to terminal 4 of the IC | Changing the fuse fm802 and the ic um801s (ice3br0665j), everything works normally. | CDS_DIAS |