SAMSUNG TV Repair: Common Faults and Solutions.
Search: SAMSUNG
Results: 3754
Results: 3754
SAMSUNG Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SAMSUNG | MX-FS8000 | Indicating protected | Shorted 10uf ac3032 capacitor and altered ar3043 4.7r resistor | Replace it and run for the hug | JOELIO SILVA |
SAMSUNG | T220M | Turns on after a few seconds and turns off leaving just the sound | Remove d201 and d202 and the lamps will remain on even if they are dim they are the plot of the lamps when they are blank removing they will remain on until they are finished | eletronica publisom egn | |
SAMSUNG | PL50C550G1 | Doesn't turn on, relay knocking | Voltage of 5.2v appears and disappears. | Replace the ci z1031 ic202 on the main board. | Pedro |
SAMSUNG | CL21C650ML | Horizontal outlet heating very quickly (q401). | C415 of 27k by 400v measuring 23k. | Ademir tc | |
SAMSUNG | PL64D8000 | Television without picture, with sound | Y-sus and z-sus board with shorted transistors. in total tsound were 4 rjp63k2 and 3 rjh30e3 | Replace and run for the hug! | PL ELETRÔNICA |
SAMSUNG | CL21Z30MQ (R) K16B | Does not turn on the stand by with voltage at +b varying from 85 to 90 volts | In my case the villain was the 913 capacitor | Replace it and give glory to God!! | Abençoado |
SAMSUNG | CL-29K40MQ | Does not turn on, when plugged into the secondary socket it rises to 152v and drops, and the primary does not discharge | 120k open resistor r821 | Replace r821 de120k | JUNIOR |
SAMSUNG | UN32J4300AG | Does not turn on, closes and returns to standibay | Short in capacitor 33 near the LED connector, this short was not in the capacitor, it was probably in ic3...but I thought it would be better to change the main board soon! | José técnico | |
SAMSUNG | UN46F5500 | Power supply with varying voltage | Ci tl431 smd | Replace of the same | ELENILSON |
SAMSUNG | UN32FH4003 | When plugged in, it keeps turning on and off by itself. | 47uf/160 backlight power supply capacitor exhausted, | Replace the mentioned parts | Edmundo |
SAMSUNG | LN32B350 | 390v low, pfc not working. | Pfc circuit | After getting angry changing the fan7530 twice and reviewing everything, I discovered that they were fake, I put the l6562a in its place and bingo! | davi.sls |
SAMSUNG | CL 21 | Normal power supply and does not oscillate | Open horizontal coil (transform) | Replace of traffic | Fofao |
SAMSUNG | CL21Z43MG KSCA. AA41 | Echoing the sides when the brightness of the image was strong | D804 and d805 in primary power supply | Just replace and run for the hug | Bynhoteck |
SAMSUNG | LE32A559 BN44-00208A | After turning it off, it will not turn back on unless it is removed from the power supply. | Check RP809, RP810, RP811, RP812, RP816 and optocoupler. | Mantunes | |
SAMSUNG | CL-21M6MQ | LED is on, when you turn it on, when you press power, the LED turns off +b and resets and the TV does not turn on | The resistor, r831 of 123k changed to any value. just change | CST ELETRONICA SERROTA SENADOR SA | |
SAMSUNG | 29K40MQ | I'm sound | R606 51k open | R606 | This email address is being protected from spambots. You need JavaScript enabled to view it. |
SAMSUNG | PL51E450A1G | It doesn't turn on, the screen flashes and no image. | Chap. ceramic na main plate ref. c226 com escape. | CARLOS-KBE | |
SAMSUNG | LN37B530P2M | Dark fabric sem contrast image type negative | Tcom board defect | Replace ci smd as15f of tcom board | EDUARDO TV AV |
SAMSUNG | PL51D491 | Turns on normally, tsound is no image and sound. The auto gen was done and passed. | Check voltage on regulators >>> ic204>1.10v, ic203>2.5v, ic201>3.26v, ic1204>3.20v, ic202>3.20v, ic2011>1.2v, ic 205>1.5v. | In my case it was the ic204 getting hot and the voltage rising. I replaced it with a z1073. the 2011 ic also has this defect | |
SAMSUNG | PL43D491A4G | No image, normal alloy, was made auto gen. On the control board, place a jumper on pins 3 and 4, turn off the main cable and turn on the TV. image has to appear. | The test was done and the image appeared, check the voltage on IC204>1.10V, IC203>2.5V, IC201>3.26V, IC1204>3.20V, IC202>3.20V, IC2011>1.2V, IC 205>1.5V. in my case it was the ic204 getting hot and the voltage rising. I replaced it with a z1073. |