SAMSUNG TV Repair: Common Faults and Solutions.
Search: SAMSUNG
Results: 3754
Results: 3754
SAMSUNG Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SAMSUNG | LN40B530P2M H40F1-9SS | Does not turn on the inverter | Place a 4k7 resistor from pin 16 of the sem2006 co to pin 23 of the inv_on/off connector | Rafael Sena | |
SAMSUNG | 29K40MQ | Turns on and off at the same time | Fell forward | George | |
SAMSUNG | UN40C6900 | Does not turn on, nor does the LED light up | TV looked like this after lightning struck near the house, right away, tsound was a problem at the power supply | The 2 fuses and the 4 1n4007 diodes of the primary power supply were replaced, the varistor seemed to be in good condition so it was not replaced, the TV started working again after changing the components mentioned. | Lucas |
SAMSUNG | UN32FH4205G | This TV arrived at my store with a very clear image, you could barely see anything. water had fallen. | On the v-com board, I identified the problem location, cleaned it with isopropanol, and found four open resistors. rg7 (9k1), rg8 (33k), rg3 (4k7) and rg2 (30r). all close to ci(ic6) | I made the replace by removing the resistors from other boards and it was perfect. | <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> |
SAMSUNG | MX-C850/XAZ | No sound in speakers | Power supply board with small signs of oxidation. | Replaced power supply board. | Aomine |
SAMSUNG | S19B300B | Doesn't start | Memory ic402 | I didn't have another one, I took it out and it worked in DVI | Eletroclaudio |
SAMSUNG | UN40H5500 | Doesn't start. When removing power from the pmain, the LEDs light up | Mcu sems31. change processor or pmain. | Eletronica Jambeiro | |
SAMSUNG | UN32FH4205G | Gray image | Qc1 and qc2 changed on the display board | Remove from the circuit and ready normal image | antonio nobrega patos pb |
SAMSUNG | PL-43F4000AG PL-43F4000AG | Doesn't start. standby led flasher | Plate and its buffer | Adriano Souza | |
SAMSUNG | P2470HN | Turns off the lamps when it changes, activates the input | Place a 100k resistor on pin 1 of the IC or 201 of the inverter | Agostinho Mariano | |
SAMSUNG | LN40C530F1M | Turns on image appears and turns off | Problem in the high voltage sector for lamps | Changing the lamp infrequently | Marcos Paulo infotron-ltda |
SAMSUNG | 32PHG4900/78 TPM15.5L | TV doesn't turn on. ci pf6003ag damaged. | High temperature when welding it. | Solder this IC as quickly as possible, at a lower temperature as it shorts out very easily. | Denys de Sene |
SAMSUNG | 32PHG4900/78 TPM15.5L | TV doesn't turn on, no stand-by. | Power supply board, CI PF6003AG (SMD 6 pins) | It was replaced by the CI OB2273, pin-to-pin equivalent. If after the replace the voltage remains low in the secondary, place a resistor of approx. 1k in parallel with the photocoupler LED. | Denys de Sene |
SAMSUNG | T220M | Turns on with sound and image and after a few seconds the lamps turn off | Burned out lamp | Replace the bulb or jam | Johnny |
SAMSUNG | CL21ZMQ KSCA | Dark screen increases screen delay line | Diodo zener dzd207 | Replace dzd207 open or short | eletronica global chiquinho |
SAMSUNG | CL21M6MQ | It doesn't turn on, it just kept the LED on, after pressing it it would go off and she would try to put it away | Polyester capacitor cr404s shorted and resistor r414 burned | Replace the cr404s and r414 | Rafael |
SAMSUNG | PL42A450 | Checkered image, and it heats up and tsound are lines from top to bottom flashing. | Controller board memory t. | To replace. the lines flash even when the flat that connects it to the main switch is turned off. | JOAOMVJR |
SAMSUNG | PL434900AG | Does not turn on, stand by LED is off, only main board LED blinks a few times | Capacitor, CS809S position open on the power supply board | Replace it and check the voltages vs,va | KL. ELETRONICA |
SAMSUNG | 2033M | Turns on and just flashes the screen and turns off | Weak light bulbs | 560Ω resistor between bl_on pin and ground. placed at the connector input coming from the main board. canceling the lamp sensor. | Cláudio A. |
SAMSUNG | LT27A550 | Screen LEDs turn off and on | Ci oz9998bgn | I replaced the ci smd oz9998bgn solved the problem | Jetro |