Tcl TV Repair: Common Faults and Solutions.
Search: Tcl
Results: 151
Results: 151
Tcl Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
TCL | 40S6500FS | Decrease the current of the LEDs | Rr36 e rr35 | Remove both from the circuit | Multimarcas/Acarí |
TCL | 40S6500FS | Decrease the current of the LEDs | Burning the LEDs | Remove r35 and r36 | Multimarcas/Acarí |
TCL | 32L2800 | With horizontal stripes / blurred image | Memory error, flash memory defect | Reset with quick on and off on the TV or updating the TV software | Gbrito |
TCL | 32L2800 | No image | Burned out LEDs (TV LEDs are compatible with models of the same letter) | To confirm, throw a cell phone light on the screen with the TV on to see if it appears immediately, without an image, then open the TV carefully, remove the screen, remove the glue from the screen with a phone card or material of the same flexibility and composition, remove the films correctly without changing the order, access the LEDs, check the LEDs, replace the bus and that's it | Gbrito |
TCL | L49S4900FS | Reduce LED voltage | Remove 2 resistors | R626 e r623 | juci |
TCL | 32S6500S | Stuck in the animation after the logo, does not initialize. | Corrupted data | Force update via pendrive, plugging it into a socket with the power key pressed. | davi.sls |
SEMP TOSHIBA TCL | LE3274 | Service mode | Input 3195 | Input 3195 | Diego Boeira |
TCL | 65P8M | No image, LEDs ok | Cm05 e cm02, na tcom | Replace cm05 and cm02 | Eletrônica center som |
TCL | L39S5900 | LEDs blink without image | Power supply defect (appears to be the LEDs) | Replace the power supply board (the one from the 40l2600 also works) | Sousatec Mauá |
TCL | 40S6500 | Reduce LED current | Remove 24k resistor connected to pin 6 (iset) of the gb98tern ci | sergio | |
TCL | 40S6500FS | No image, dark image, black screen, after turning on the image disappears. | Burned out leds | Replace bars with new and original ones and reduce the LED supply voltage by removing theΩ resistors rr35 and rr36, which are located close to the LED power connector. | Adriel SS |
TCL | 55P6US | No image - normal sound, normal backlight | The display itself, manufactured for tcl by csot, has a chronic defect: the screen transistors (tft) short out and do not allow the screen to arm the dc-dc power supply, remaining in protection, with hvaa, lvaa, vghf absent or with changed values. The slightest knock on the corner of the display can cause this defect. | Tsound is no solution, if this defect is found, the screen is unusable. | victor paz |
SEMP TCL | 32S6500S | Does not turn on, not even the STBY LED lights up. Source ok voltage only on D801 45 volts, LEDs tested all good, change regulator UD18 1.8v | In my case it was the reg ud18, it killed an input voltage of 3.3v and did not output 1.8 volts. | Davi | |
TCL | L39S4900 | Image flashes when it heats up | 1 LED bar with 01 burned out LED replace bars | reginaldo moronte,eletronica junior caldas novas | |
TCL | 50P8M | Image split in half | After changing the main board, the image was split in the middle of the screen | Press 062598 menu (control lines) and enter the ID of the old board, in my case 115 but it could be 034, 354,365,205, or 057, the TV will restart and return to normal! | Tv Técnica Prudentópolis |
TCL TOSHIBA | 40S4700FS | Burnt voltage regulators next to the LVDS cable plug on the main board, Q900, Q901. | Oscillations in the electrical power grid apparently. | Replace voltage regulators next to the LVDS cable plug on the main board, Q900, Q901. | Adriel SS |
TCL TOSHIBA | 40S4700FS | No image | Burnt voltage regulators next to the LVDS cable plug on the main board, Q900, Q901. | Replace voltage regulators next to the LVDS cable plug on the main board, Q900, Q901. | Adriel SS |
TCL | 55P65US | Reduce LED current to increase life expectancy | Increase theΩic resistance value between pin 2 of the ci ob3365 and gnd | davi.sls | |
TCL SEMP | 50P65US | How to reduce the current of leds | Change the 10k smd resistor r613 for another 330k resistor I put 470k this resistor is close to the IC | badri eletronica <small>This email address is being protected from spambots. You need JavaScript enabled to view it.</small> | |
TCL | 32L2800 TPD.NT72563.PB772 | Decrease the current of the LEDs | Resitores | Replace the three resistors (0) connected in series to three (4r7) | Multimarcas/Acarí |