Search:
Results: 87417

Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
SONYKV1954R
Need p/n for uhl switches, part of rv001 1-228-943-00I need the p/n for the u-h-l switches on m-2 board. -hq comments: the switches in question are part of rv001 volume block,preset (p/n 1-228-943-00). the whole block has to be replaced.
SONYKX2501A
Picture fade in and out, replaced q1320When set would get warm, the video information would fade inand out very slowly. by keeping q320 turned off, the video would notfade. everytime the video started to fade, the base of q320 would go lowand it would turn on. found q1302 on bd board was l
SONYKV2680R
No sound, replace ic-1106 on x boardThis unit had no sound. when off station, a rushing soundwas present, however, when receiving a station the audio was completelymuted. we found ic1106 to be defective.
SONYKV2675R
Aft osc, cold solder on aft coilChannel would oscillate in and out of frequency about 1/2cycle per second (vc voltage was varying at the same rate).
SONYKV2670R
Dead, replaced crt, h out and r-608The set went dead and smoke rolled out the back. we foundr608 to be the cause of the smoke. furthermore, q504 was shorted as wasthe crt. the strange part of this failure is that both fuses were intact.
SONYKV2649RX
Immediate shut down, replaced hvr blockSet would come on and immediately shut off.
SONYKV2649RX
Dead, replaced h out transistorSet came in dead. found horizontal output shorted.
SONYKX2501
Bullets in picture, grounded crt pin 10The unit had bullets on the screen even with no video input.it appeared to be caused by some kind of corona discharge. furtherinvestigation revealed pin 10 on the crt to have a charge. this pin isnot connected to anything on the crt board. grounding t
SONYKV1948R
Picture distortion, replace c654The picture was pulled in on all sides and was snowy. wefound all b+ power supplys to be low. the 135v power supply was about 103v. regula-tion was poor. increasing the line voltage to 140vac resulted in normaloperation. we found c654 which is across t651/pot t
SONYKV1941R
Video drift, leaky d2213On low channels video would drift.
SONYKP5040
Incorrect mechanical operation, adjusted gear ass'ygNew arm assembly was installed. door would not close all theway on right side. found large gear off one tooth on gear strap inassembly.
SONYKP5040
Incorrect mechanical operation, replaced arm ass'yMirror would not extend to complete open position.
SONYKP5040
Buzz in sound, adj helical filter and replaced aft with rBuzz on some cable channels. this complaint was pending sincedec. two trips were made to the customer's home. on the first trip iadjusted the helical filter which removed most of the buzz.
SONYFD30A
Poor vhf reception, ant contact plate a missingThe reception on vhf low channel was very poor.
SONYKX2501
Mechanical popping noise, tighten cabinet screwsThe customer said that the set made loud popping noises evenwhen turned off. the sounds were caused by the cabinet contractingduring temp changes. we found the screws mounting the mask to the maincabinet loose by 2-3 turns each.
SONYKX2501
Immediate shut down, replaced r1602Unit would go into shut down within 2 minutes of turn on.found r1602 open. replaced with another 24Ω resistor and performedmanual check for shut down circuit.
SONYKV2649RX
Dark picture, add cap to c546When viewing scrambled channels using the jerrold cableconvertor box, the picture is very dark with smeared reds.
SONYKV2648R
Audio noise in matrix, resistor changeWhistle in matrix audio only. the countermeasure given to meto resolve this problem worked.
SONYKV2647RX
Picture distortion, poor grounding at rca type connectorWeavy red lines from top to bottom about one inch thick onlow vhf channels. also radiating to other sets on same antenna line.
SONYKV1515
Buzz in soundBuzz in sound on showtime scrambled cable channel only. allother channels ok. verified problem, noted that several older sonychassis in same house worked ok (including kv-1710/1941r/8000).