Aiwa TV Repair: Common Faults and Solutions.
Search: Aiwa
Results: 309
Results: 309
Aiwa Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| AIWA | JAX-PK33 | Device works, has no display | R908 open on transformer board | predador403 | |
| AIWA | JAX-PK33 | Device works, has no display | R908 open | predador403 | |
| AIWA | CX-NS305-LH NSX-S305 | Turns on at the same time comes back stand-bye | Transistor output short sound, q214-b1626, q212-d2495, was replaced and the same thing happens. | Replace sound outputs, and see there the transformer has a plate with a resistor type (pr005) it is open, put resistor 1r, putting vo, it works | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| AIWA | NSX-SZ21 | Doesn't read cd | Unit not found ksm-880 replace with sf-p101 not with kss213 keeps failing | Paulo.nickel | |
| SOM AIWA | TODOS | Optical unit skipping skipping tracks | Defect in the unit cart motor, | Replace the engine. obs. To avoid warranty problems, replace the optical unit, preferably the original, good luck, professional friends. | fernando timbauba PE |
| AIWA | AR295 | Does not turn on, normal power supply | R808, 816, 823, 836, 840 changed check all of 4k7 | amsmariano | |
| AIWA (SONY) | CX-NJ3 | When you increase the volume it only turns off | Faulty protection capacitors are 0.22x2w position on board r149, r150, r151and r152 | Replace the four with similar parallels or originals | jerson 37 |
| AIWA | CX-NSZ51LH | Turns off when the sound is powered | Turn off transistor q130 | caio | |
| AIWA | CX NS 888 LH | Red LED lights up but just clicks on the relay and nothing lights up | Pro 005 open and diode 001 changed | moroni eletronica | |
| AIWA | TV-AR295 RHB | With excess green and retrace of white lines. | The transistor q 710 shorted smd, thus increasing the voltage to 9 volts on the g output pin of the ic 101.. | Your replace. | house eletronica ltda |
| AIWA | NSX-V420 | Panel functions do not work correctly, only on the remote control | Solution: replace all touch switches | patrick | |
| AIWA | NSX570 | When I raised the volume the device turned off completely. | Q214 q215 smd can't be measured just by changing | vagner nardes | |
| AIWA | TV-C1400EZ PT23CO | It didn't turn on or show a stand by signal | 390k resistance r804 open | 390k resistor replacement | LASC |
| SOM AIWA | CX-NF969 | Shutting down, going into protection | Q224 k2937 | Replace it, I couldn't find another one, I called it without it and it worked | This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós-PI,Ohm eletronica |
| AIWA | NSX-F12 | 5 cd carousel, motor does not have the strength to turn the carousel | 33Ω r changed CD board feeds q401 to 406 | Bruske | |
| AIWA | NSX-999 0118 | Panel lights up weak | Electrolytic c108 c107 | Solved | EDSON |
| AIWA | NSX-S22 | Nothing appears on the display | Open 27k resistor r116 is at the power supply | ||
| AIWA | AR295 | Power supply a little higher than normal and ticking on the power supply relay. does not generate high voltage. | 127k r820 open | Replace r820 | Edson S.A. |
| AIWA | CX-81MH | Display does not light up | Check c107 and c108 of 22uf | MATA | |
| AIWA | CX-81MH | Display does not light | C107 and c108 of 22uf dry | MATA |