PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH21M SS | TV inoperative and led pool | Change from-811 to-813(byv95) dz18v in the line of r818 q-802 and r826 | samuel leite | |
PHILCO | TPF2121C | TV turns on with sound popping and no image and turns off | R910 and r912 open | Just replace and run for the hug | Junio kleber |
PHILCO | PH21 MSS | Does not leave st. by. Because of a memory problem, I posted this defect and forgot to say that if anyone needs the eeprom, ask me by email: This email address is being protected from spambots. You need JavaScript enabled to view it. and I'll send it, ok? | Memory swap | reinaldo almeida | |
PHILCO | PH29M SS | Low power supply around 40v LED goes out but the TV doesn't turn on the power supply stays the same | C851 .1 with leakage is at the base of q808 | Replace c 851 | Damião |
PHILCO | TV PH21MSS | Does not leave st. by. | Memory, but be careful, I had already installed another one that I recorded with files downloaded from the internet and it didn't work, it only worked when luckily another TV like it came on and I copied the files and switched to the one that had the problem. | reinaldo almeida | |
PHILCO | PH21M SS | When turning it on, the LED flashes, +b changing to 24v | D818 =fr104 shorted | Replace it and run for the hug | hipereletronica service (maraial-PE) Marcelo |
PHILCO | PH 21C | Turns on with vertical closed, then turns off | D 810-replace open diode | MARCELO JOSE | |
PHILCO | TTV PH 21C | TV does not turn on any voltage on the secondary | Zener diode 12v short non-primary d821 | Darci Fuhr | |
PHILCO | PH24A | Does not turn on, power supply stopped | C203 (2n2/ 1kv polyester capacitor) shorted | Aecio Flavio | |
PHILCO | PCS2956 | Risk on the image, better known as the delay line, which is generally seen on the c728 3n3 1600v | C728 3n3 1600v was replaced | gerson tomaz | |
PHILCO | PH29 | Does not turn on low power supply | Zd804 (4v7) | mega center | |
PHILCO | TPF-2922 | Vertical burnt out, the biggest problem to fix, I used a similar part and it never worked. | The resistor that comes from the 50volrs of the flyback is 18r and the ci tda8177f or tda9302h there is no point in putting the tda8177 | Put the correct parts and that's it, blz | fabiusmax |
PHILCO | PCM-2046 | The standby LED doesn't turn on, it's flashing, only the flyback is defective, be careful friend, even with the +b and the bu disconnected, the power supply is low @@@ | Flyback | ELETRONICA ARNI/LEOBERTO LEAL-SC | |
PHILCO | TPF2922 | Burnt resistor r709 | Value of resistor r709 is 18r 1/2 if you put lower values it will burn type 1r it will catch fire | fabiusmax | |
PHILCO | PCM-1451 | Call whenever you want, it seems like a bad connection | Intermittently turns on and off... | Changing capacitors c 709, c708, changing both without measuring.... | Adriano,rio verde,MS |
PHILCO | TPF2121 | Altered power supply, (+ b quese 170 volts.) triggering protection. | R919 - (120k) fully open. | Carlos Maia | |
PHILCO | TPF2121C | Vertical closed | Chap. c614 shorted 47nf ceramic | Replace component note: short on the scale x1 this one is actually shorted, hugs | FABIUSMAX |
PHILCO | TP20V56 | Image disappearing brightness, starting at the top, normal sound. | D 602 as leak | aelson | |
PHILCO | PT1410 | Inoperative, led off. | It was the broken q901=stp9nc70zpf mosfet, ic901=ta1507p, r918=2k2 starting. I changed it and left for the hug. | ELETRÔNICA MELO BOA VIAGEM -CEARA | |
PHILCO | PCS-2700 | (correction) TV without +b on the secondary, with blinking LED | As previously reported, the capacitor (c 720) is not 10uf but 47uf | Ademar / Videira sc |