PHILCO TV Repair: Common Faults and Solutions.
Search: PHILCO
Results: 4741
Results: 4741
PHILCO Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PCS-2976 | Dark stripe on the left side | R 712 10k changed | ELETERONICA ROBSON(DEBIQUE) | |
TV PHILCO | PCM 1444 | The TV had a blinking LED, worked normally and had stripes on the left/right sides. | R-719 open | Replacement | wagner |
PHILCO | PCM 2046 CPH-05M | LED flashing and when I opened the flyback screen the vertical appears closed with the line reduced, as if it were a flaybk power supply | Ic 701 is what powers the hvcc of the 8361 and vcc of the vertical pin 10 | I replaced it and it worked normally. good luck to everyone | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | TP14U56 | Does not oscillate (turns on). normal voltages. it is only on standby. When you press power it makes tick tick tick and stays on stand by. | I released pin 3 of the photo coupler and then the TV oscillated (turned on), then turned off. I noticed that the vertical core overheated in 3 seconds. so I killed the charade. la78040n. | Tec vídeo | |
PHILCO | TP 1410 | The TV tries to turn on, the LED goes off, disarms the demagnetizer relay, then the LED starts blinking, it doesn't work. | Resolve or exchange r 931 | caio | |
PHILCO | PCM2051 | TV with sound; no image, no brightness | C 801 on the trc board | After the replace, everything shine appeared | ELETRON ICA ROCHA FERNANDO ROCHA |
PHILCO | PCM 1444 E OUTRAS | Mirror image | R 718 open | Master | |
PHILCO | TPF29S4F | Closes image in the corners, cushion or cup effect, does not correct pincushion. | D1702 with oxidized terminal glue. | Bruske | |
PHILCO | TP14U56 | Turns on and after 3 to 5 seconds turns off. | Bad solder in the photo coupler region | I observed that all voltages were normal. and I noticed that it oscillated and when it was about to light up the tube went into protection and the LED kept blinking. That's when I suspected the photo coupler region. As I didn't find any defective components, I decided to re-solder that region and it was ok. | Tec vídeo |
PHILCO | PCM2044 | TV turns on and off by itself, sometimes it takes a few minutes | R713 open | juci | |
PHILCO | TP-2054 | The device is turned on, the screen turns red with incriminate traces, after a few seconds it goes into stand-by, | Metal film resistor, value 10k, on the kinescope board, referring to the red cannon drainer transistor, replace it, it is ok. | CLÁUDIO RIBEIRO, TECNOSAT ELETRONICA E INFORMÁTICA, JATAÍ-GO. | |
PHILCO | TPF2130 | It turns on but when the relay goes off a brief image appears with the frame closing horizontally, it goes to stand by with the LED flashing. | C701 (horizontal deflection) auterated | Replace the c701 (8.2 nf/1.6kv) | Ricardo Moreno |
PHILCO | PCS 2956N | High voltage spikes and turns off | Width defect, replace 8n2 and 4n7 ceramic width capacitors and increase the vertical output transistor decipher (2) | Prado | |
PHILCO | PC2956 | There is no voltage in the secondary of the power supply, it just pulses. | C-921=1k per 1kv of shorted disc, only replace with one of the same value, if not the voltage variation. | It was replaced for one of the same value and it was... ok. | Armando da Eletrônica só Tv. |
PHILCO | PCS2952 | It keeps beeping, beeping and the LED is blinking. | Q 902. | I started it off and it worked. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | TPF 2140 | It doesn't turn on and it doesn't work on standby. | C 930 with leak in the power supply primary | levilp | |
PHILCO | PCM2044 CPH05 | Vertical fexado. | R.602 | Replace. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
PHILCO | PCS-2956 CP-01-LR01 | Power supply does not start and chopper driver smokes on pin 7 | C922 short (1.0 nf) I replaced it and the problem was solved. | Note: as the c922 is on the pulse line (130v) the power supply activates and disarms successively. | Tecnogil Eletronica |
PHILCO | PT20V56 | Vertical beam and then switches off | Ceramic capacitor c614 | ELETRONICAAC | |
PHILCO | TP20V56 | Vertical beam and then switches off | Ceramic capacitor c614 | Ac electronics |