PHILIPS TV Repair: Common Faults and Solutions.
Search: PHILIPS
Results: 14171
Results: 14171
PHILIPS Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILIPS | 20PT 3336 | No image, just characters | Swap r-3442 and r 3459 is close to the fly back | Ademar / Videira sc | |
| PHILIPS | 3331 | Reduced frame and power supply with 68 volts on the secondary | Change the r 3526 without testing the value of 0.15r connected to the fet | Ademar / Videira sc | |
| PHILIPS | 1340 | Green screen with lines | Touch zener diode (zd 359) 3.9 volts | Ademar / Videira sc | |
| PHILIPS | CHASSIS L-04 L-04 | Turns off with error 11 | Change coupler photo | Ademar / Videira sc | |
| PHILIPS | TODA LINHA GR-1 | Jagged image | Replace r-3226 (18k) | Ademar / Videira sc | |
| PHILIPS | 29PT4635 | After 5 minutes the video disappears and there are only characters, also on the av. | Replace ic 7200 o micro. | Henderson(hndrsn) | |
| PHILIPS | 14PT3336/78 | TV with broken board, restoration was done and the TV started working again, but kept turning off | Solution: adjust the screen. and the TV was ok. | Carlos | |
| PHILIPS | 23PFL5522D/12 LC72ELB | Does not turn on, LED of, power supply vibrates | Na power supply d205 (sb360 ,3amp 60v) | Replace c24 (331k/3kv) | J.CUNHA |
| PHILIPS | FWM57 | Damaged by lightning (dead) | After a lightning strike, he was dead, with the display completely turned off. On the power supply board I found inductor 5929 open, whose value indication in the diagram is 1m. as inductor 5931 also has the same value, I measured its resistance and found 12Ω. So I added three identical inductors (from a piece of scrap) which together gave almost this much, I replaced them and the device was perfect. In the open inductor I could notice that the wire was extremely thin and despite it being in series with the 200 ma fuse 9902, it will certainly always open before the fuse, in case of overload. | littlecarlos | |
| PHILIPS | 29PT4635/78 | Dead power supply does not turn on standby LED does not have +b 140v +b12v | Capacitor 2521 22mf 50v | Replace with new | brancobilli |
| PHILIPS | 20PT4331 L03.1L | It turned off after 5 seconds. error 11 in service mode | Resistor 3443 (3r9) resistor 3444 (4r7), resistor 3403 (340r) overheated and altered | Replace for another of the same respective value | djeferson hoed |
| PHILIPS | 14PT316 | Does not turn on LED does not light up | It had 170 volts in the primary power supply but c.i. The power supply oscillator had no power supply, I found the 6540 diode (bav21) shorted, I replaced it and still there was no voltage, I replaced the c.i 7520 and the TV started working again | JOSÉ GUSMÃO | |
| PHILIPS | 14PT3331 L03.1LAA | +b oscillating. TV doesn't turn on | R3524 smd em curto | paulorusso | |
| PHILIPS | 21PT6456 L03.1 | Fountain chirping does not turn on | Capacitor 2424 next to the flyback | Ozias | |
| PHILIPS | 20PT 326 | No color | For no apparent reason | Enter service mode, type 062596 see sy option and put it in 2 or 3 and go to hug | Ademar |
| PHILIPS | 20PT 3331 | No sound | For no apparent reason | Remove the diodes d6809 and d6808 and leave them without them | Ademar |
| PHILIPS | 29PT 9467S | No image, increasing screm return stripes | Fuga do fly back | Check abl line and replace 1k resistor (r 420) | Ademar |
| PHILIPS | 29PT 9467S | Cushion effect | Fuga do fly back | Replace q440 (irfs 630) and 8.2 volt zd441 zener diode | Ademar |
| PHILIPS | 29PT4635/78 | The TV would turn on, the plot would appear with interference and immediately the horizontal would burn out. | 47x25v 2455 capacitor with little capacity. | I replaced it and the TV was great. | nachbar |
| PHILIPS | 14PT3131/78R L03.1L | Resistor position: r-3403 to 470r open | Getulio |