Search: PHILIPS
Results: 14168

PHILIPS Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PHILIPSA8
Hotel modeFollow the same procedure for hotel mode as l7l. put it on channel 38 and press vol(+) simultaneously with vol() on local panel and osd on remote control * 08jun00 anc * .
PHILIPSA8
Blemishes in the image (lack of purity).M.c. no ptc. *05ago98 h.desk*
PHILIPSA8
Horizontal lines (bottom or top).When turning on the device, horizontal lines appear on the higher, this occurs due to the low beam current in this moment, to attenuate this effect, enter adjustment mode in the page 7 and change the vershift and verheight, then save the data
PHILIPSA8
Dos / menu - does not leave the screen.Letter s does not leave the screen (service mode).replace eeprom 7620. *01set98 h.desk* before replacing the eeprom enter adjustment mode and check the option bits. * 11oct2000 anc * .
PHILIPSA8
Turn off inter. or protect (rew 3 for vcr).Possibility of cold soldering on jump 9914 or photo coupler 7904, also check possible changes to: 3926, 3944, 3976 and 7904. 21Jul00 jpba
PHILIPSA8
Damage IC or TS semiconductorIntegrated 7150 (tda8844), probable fly back leak. * 05Oct99 jpba/nk *. transistor 7325 (bc857) and diode 6325 (bas216), it can also damaging the integrated 7770 (tda9178 4806 209 87826) is likely short on tsh 5630. * 03dec99 acm *.
PHILIPSA8
Poor contrastLow contrast can be caused by bimos(7225) with wrong version. the correct mask is 9722 3y. the mask wrong could be 9623 2y. *05Aug98 h.desk* check integrated 7770 (tda9178 code 4806 209 87826) on p
PHILIPSA8
Commands act partially or hotel modeActivate volume (+) () on the panel at the same time with the key remote control osd. * 22Feb2000 anc *.
PHILIPSA8
With interference lines.Replace the 47nf capacitor 2207 with 100nf. * 03Dec99 acm *.
PHILIPSA8
Menu appears when changing with remote.Check batteries, they may be weak. * 25set00 jpba hd *.
PHILIPSA8
Appears dos/menu - blinking.When changing channels, check the remote control batteries, when weak, it causes information errors. * 11oct2000 hd * .
PHILIPSA10
Dark "black" screen (see also bril4).Check tsh (fly back) 5431. iris: symptom 111, section dfl, repair a. * 01feb2001 iws report from germany *. check integrated 7830 (tda6107q). 04May01 fcr dreux *.
PHILIPSA10
Fade colors after heating.Check the bocma on the ssp panel, if not available replace ssp panel. iris: symptom 410, vpa section, repair the. * 01feb2001 inf iws report from germany *.
PHILIPSA10
Squeaky soundTry replacing 2424 capacitors from 12nf to 11nf and capacitor 2416 from 1.2nf to 2.2nf. iris: symptom 540, section dfl, repair a. * 01feb2001 inf iws report from germany * .
PHILIPSA10
So fica em stand by (power off).Only LED is on (error 2), check vbat voltage on tansistor 7481, welding problem may occur on pin 1 from ths (fly back) 5431. iris: symptom 110, dfl section, repair d. * 01feb2001 inf iws report from germany *. check rg amplifier
PHILIPSA10
Tuner with little gainCheck if the tuner is soldered. iris: symptom 341, tun section, d (chass) repair. * 02Feb2001 inf report from s'pore *.
PHILIPSA10
No voltage (vo, +b, hvt, etc.).No voltage g2 (dark screen), check tsh (fly back) 5431. iris: symptom 111, section dfl, repair a. * 01Feb2001 info iws report from germany *
PHILIPSA10
No sound. (with or without image for TV, VCR).Check 7704/7710 (bc847b). 04May01 fcr dreux *.
PHILIPSA10
Noise when changing channels "plop"Check value of the elco 3.3 uf 2705 capacitor on the panel lsp. * 14Feb2001 ehv ran meys st01/0006 *
PHILIPSA10
Concave framework ( ).Check geometry adjustment (eastwest correction). iris: symptom 338, section dfl, repair c. * 01feb2001 inf iws report germany *.