Search: Panasonic
Results: 2880

Panasonic Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PANASONICTC20A04
TNP4G269
It turned on and off in a few seconds.D1140 was shorted, arming the protection.Eletrônica do Jordão -PI
PANASONICTC-L32B6B
Burning ledsVoltage found on the LEDs, 75v. the expected is 66v. This model uses 3 bars containing 22 3 volt LEDs (each LED). the total sum becomes 22x3=66v. This (66v) is the voltage that the LED set supports.Remove the resistors (20Ω) r251,252,253,254 and replace the value of r255 to 33Ω. the voltage will drop to 66.7v.Evando Viana
PANASONICTC-40DS600BE
Backlight flashes 3 times and turns offMain board memoriesReplace the memories on the main board, otherwise replace the board itself.Douglas
PANASONICTC-14RM15L
TV turns on normally and switches to AV when you put the converter on, the image is darkThe defect was the open 95.3k resistor r557 and one of 100k
PANASONIC TC-L32C10B
I'm soundRemove the transistor q5450Bruno nicacio
PANASONIC TC-L32B6B
All blue screen has soundMeasure the voltage of the t-with a lack of 12v, the main board came with 0v, close to the lvds connector, tsound are 3 smd capacitors, 2 small and another slightly larger one, I removed the larger one from the board, it was shorted c4002 4.7uf 16v smd it is killing the 12v voltage and replace On the other hand, the TV normalized the imageDefect resolvedAndré
PANASONICTC-32A400B
KM25 / KM26
LED constantly burningStandard voltage at the output for the LEDs - 70 ~ 72vRemove the r7839 which is on the top and the r7825 which is on the bottom, leaving 64 ~ 66vmarcos
PANASONICTC-32A400B
DeadOxidation on the signal boardResolder transistors and smds capacitors.Multimarcas/Acarí
PANASONICTC-P50V20B
Doesn't startIC501 insulation broken.Replace ic501 and f501.electronics supply parts - Gramado/RS
PANASONICTC-20G12
TV keeps hitting the relayThe cause was the 2kv capacitor c565 222jnaelson silva gravata pe
PANASONICTC-32A400B
Doesn't startA ram at the power supply, it only burned rifleReplace rifle and remove ramDinho
PANASONICTC-L42U30B
Led flashes 14 times 15v low voltage with 5v customer 88178817R901 amendedTrade for a 36kMARCOS MELO
PANASONICTC-L42U30B
Doesn't start. red LED flashes 14 times low power supply defect. it is giving 5 v on the 15v line pins 456 power supply cableDoing a test on the IC 803 circuit I found a 30.1k resistor r901 changed, I put a 36k one and replaced it with 17 volts customer 88178817Replacing the r901 resistor with a 36k one click 88178817marcos melo ce
PANASONICTC-14A12
Power supply floating and turns offPower supply coupler d807Replace of the sameELETRONICA SALES.NATAL RN
PANASONICSA-AKX10
It turns on normally for a while and turns off. then it doesn't turn on anymore.I found the capacitor in position c5817 at the power supply, exhausted. It was replaced and the sound worked normally again.Carlão
PANASONICTC-32C10B
Stop10rx5w open resistorReplace resistor r880 10r x 5w near the relay and run for hugVICTORINO
PANASONICTC-14RM15L
It turns on and off, the screen doesn't turn on and the standby keeps blinkingI removed the q581 and the TV turned on with half the screen closed. the cause was r405 of 2.7kResistor r405 de 2k7naelson silva gravata pe
PANASONICTC-39AS600B
Turns on, LEDs flash, turns off and remains in stand-byChanged bar (check if tsound are any burnt bars)Jumper r4, r9, r31 r33 (they are all gnd), note: I recommend reducing the voltage of the LEDs from 3.3v to 3.0vJunior Souza
PANASONIC TC21FX32L
When you plug it into the socket by pressing the power key, it just lights up the LED in green, then you pay and end up with the c856 charger, nothing turns onQ850a1668shortI put another one from a scrap bimba TV, it focused well againMarqueis eltec eletrônico
PANASONICTC-L32C10B
Turning off and secondsArcing in lamp socketsSimply insulating and cutting out the burnt plastic was a breeze! good luck!!Jhone eletronica