Panasonic TV Repair: Common Faults and Solutions.
Search: Panasonic
Results: 2880
Results: 2880
Panasonic Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PANASONIC | TC-29G11 | TV activates relay but does not turn on, LED remains on. | Open zener diode 602. replace with a general use or make a jump. | MANTENOPOLIS | |
| PANASONIC | TC-21FJ32L | PC860 photo sensor next to the power supply driver in the test was good, replaced it and solved the problem | fabiusmax | ||
| PANASONIC | KL05 | Doesn't start | L c394 | Replace of the same | misso |
| PANASONIC | GT-1422 | Doesn't start | B+ shorted to ground def. power supply c823 471/1kv shorted | ELETRONICA ARNI - L. LEAL | |
| PANASONIC | TC14C06 | Just catching channel 02 with drizzle | R1186 (180r) aberto | Luciano Fontes | |
| PANASONIC | 20G9 BRD1 | Blowing the power supply fuse | 10k open resistor r-833 | Replace the resistor | edsontadeu |
| PANASONIC | TC20A7 | Dead | C652 de 680pf x 2kv alterado | Jaison | |
| PANASONIC | 14A10 MX5 | I didn't tune in to cable channels | Varicap replacement | sergio luiz | |
| PANASONIC | 14RM10L | Blocked channel, | Press volume- on the panel and sleep on the control | beto2828 | |
| PANASONIC | TC 1404 A | TV works normally +or- 30 minutes later protection works by unplugging it from the socket and starts working again for a little longer and the protection activates again | C559 7n5 x1600v | Rolf Thomas This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| PANASONIC | TC-20A12 | When turned on, the TV oscillated and gave normal sound, but tsound was no high voltage. | I checked everything was normal. I went to the bus and found that it did not collect the voltage from the faly back but did not emit it. | It was raw solder on the bu emitter, I resoldered it and it was fine | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PANASONIC | 14C6 | TV makes a buzzing sound at the power supply and doesn't oscillate without +b on the horizontal output | Replaced d 835 short | jaironuness | |
| PANASONIC | TC-20A12 TZGNPAL20A12 | When the TV is turned on, it has normal sound, but not the image, it oscillates but not the voltage. | Flayback kft3aa428f, and I just change it and go for the hug | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| PANASONIC | SA-AK230 | When turned on, f61 appears on the display | Dz 5808 5v6 short | Daniel | |
| PANASONIC | TC-14A12 | Tv turning off | R 631 of 560k open | Daniel | |
| PANASONIC | TC14A10 MX5 | Inoperative - after several tests, zero voltages were found on the ic 401, the power supply pins were raised and the voltages returned to normal, the TV turned on and came back with the vertical closed. The ci was replaced and it started working again. | Replace ic 401 la 7840 | Jaison | |
| PANASONIC | TC-20C4 | TV without green in colors predominates red and blue | Changed at r- 330 hms on the tube plate. | jaironuness | |
| PANASONIC | 29" | TV when you turn it on it makes noise and for the LED it reduces its intensity and the power supply becomes low because you keep trying to turn it on and off it ends up working normally I would like to ask my friend for a tip! | Thanks for your attention, thanks | francisco | |
| PANASONIC | TC-14A12 | Protection | Q401 e r401 | alan | |
| PANASONIC | TC-20C7 | Alloy does not oscillate, kills 90v | Ic 401 la 7837 vertical | I replaced it and it worked normally | Eronaldo |