Search: Panasonic
Results: 2880

Panasonic Repair Guide: Common Issues and Fixes

Brand Model Fault Detailed Problem Solution By
PANASONICTC-20A7
MX3-R
No video (gray screen)Q150 (2sc-945)A bc338 can be placed in its placeBruno.
PANASONICTC-20A7
MX3-R
Acting protectionIc401 (saida vertical)Just remove the integrated one and connect without itBruno.
PANASONICTC-20A7
MX3-R
Don't tune in to any channelR1180 (10k)Bruno.
PANASONICTC-20A12
Turns on and off non-stop: the TV normally stays on for a few minutes, sometimes not even a minute, then it starts to turn off in short intervals of half a second or less, disappearing and the audio and video returning.Solution: d1105 in short, the 5v regulator ic1205 that feeds the circuit of this diode which is the CR receiver among others was overheating due to excess current and causing it to trigger protection, not that of the TV but that of the ic1205 itself doing the even turn it off, but when the voltage reference at its input changed, it turned it back on again, which caused the defect.This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONICTC20RM10L
Completely inoperative, standby LED does not light up, 5 volt power supply for the 3.3 volt regulator lowShorted remote control sensorReplace sensoralexsts
PANASONICTC20A6
TV didn't pick up channels, just blue screenResistor r106 (470k) openThis email address is being protected from spambots. You need JavaScript enabled to view it. BRUNONIKACIO@HOTMAIL
PANASONICTC-14A12
Turns on but after some time it keeps turning off and on when acting on the screen you notice that the screen shrinks and expandsLeaky coupler photo. d807gilsce
PANASONICTC-20A12
BR3L
Turns on and off non-stop: the TV normally stays on for a few minutes, sometimes not even a minute, then it starts to turn off in short intervals of half a second or less, disappearing and the audio and video returning.Cold and/or broken solders, I noticed that the power supply's secondary diode had their solder not completely cracked, but even so I refilled these and the others that I found throughout the board.This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONICTR-1020P
No audio.Broken audio flat cable.Carlos André Poloni
PANASONICTC 14A7
Doesn't startEither horizontal or verticalReplace mentioned componentseletronicaapolo
PANASONICSA-AK110
Stand by does not light up, panel does not light up and does not turn on.Fuse f2 open and zener d964 shorted.Replace fusivel f2 de 1.2amp e zener de 7,5 volts.ELETRONICA SÃO FRANCISCO This email address is being protected from spambots. You need JavaScript enabled to view it.
PANASONICTC-14C5
With sound and no imageTelevision with sound and no image (no voltages on the kinescope PCI), normal power supply voltages, low horizontal output transistor collector voltage (25v), low vertical voltages. removed the vertical ci (ic401) television returned with the characteristic feature (pci kinescope voltages "appeared") and then replaced normal image.PY3IG
PANASONICTC29FX30
Inoperative (all normal voltages)Crystal x 601 of 20.25DEBIQUE (ELETRONICA ROBSON)
PANASONIC20C06
Hitting the power supply relayCauses r832 of 5k6 open and bad ci fd312sluiz carlos
PANASONICATC14A8
No audioAlto falanteReplace the speakereletronicaapolo
SOM PANASONICAK-25
Remote control doesn't workIc 901 curto no pino 31 do microChanging the PC To handle the PC, use surgical gloves and a soldering iron up to 30W, preferably isolated from the mainsflavio
SOM PANASONICAK-25
Display offReplace displayflavio
PANASONIC29KL05
Power supply changing and TV doesn't workCi p w6756It gives us phonitan
PANASONICTC-20A12
Low channels (2 to 6) normal and high channels (7 to 13) image disappears from time to timeTnr001 (varicap) defective.Original env56d75g3r --> compativeis tedh9-301a env56k05g3 env56dd7g3 env56dd7g3-b j3aaaab00002 env56k19g3f env56k23g3fHelio Fernando (ELETROSONIC)
PANASONIC29S10
Inoperative contrastR563Replacefernando timbauba PE