Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4758
Results: 4758
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | TP29C21 | When the TV is plugged in, it activates normal stand by, but when you press the power key, the LED goes off as if it were going to work and nothing, only the LED keeps blinking | Lack of -12v voltage on the power supply secondary | D 909a shorted, r 912 and r 910 open. When replacing the TV it worked normally. | Eletronica Som & Imagem |
| PHILCO | TV PH21SS TV PH21SS | Nâo liga nem led stand by | R520=120k | In my case it was (r520=120k) - it worked 100% | neupsx4 |
| PHILCO | PH 21C | Does not turn on, device inoperative +b only 30v and does not oscillate | 3v3 supply failure, diode d872 shorted causing the defect. | Replace 3v9 diode d872 | celinvds |
| PHILCO | TP1454 | When a vertical line appears on the screen, when viewing the video, the screen opens and closes with retrace lines | C730 - capacitor de largura horizontal 6n5 x 1,6kv | Domingos da Eletronica | |
| PHILCO | PCM1446 PCM1446 | Fire broke out on the flyback | Holey flyback | I replaced the flybek and it worked right away. this tip is great | kynnka |
| PHILCO | PH 21C | Low power supply +-80v partially closed frame | Place 1 22k resistor in series with the power supply reference resistor | warley cesar | |
| PHILCO | TP2054 | Does not work. | Fuzivel quimado | Blown fuse due to shorted c-909 | RAIMUNDO |
| PHILCO | TP2053 | Power supply does not oxidize | Tsound was no 11 volts on pin 14 of the ci 901's vcc and tsound should have been 11v on pin 2 of the ci 901 in staby, c 917 and c 907 smd with leak | BRUSKE | |
| PHILCO | TP2054 | Power supply does not oxidize | Tsound was no 11 volts on pin 14 of the ci 901's vcc and tsound should have been 11v on pin 2 of the ci 901 in staby, c 917 and c 907 smd with leak | BRUSKE | |
| PHILCO | PH14D | Completely inoperative power supply stopped | Q801 | carlinhos100 | |
| PHILCO | PCS2976 | Cut-off tube | After changing the tube, flyback, and vertical output it worked without sound | Replace eeprom | ÁdrianChapadãodoCéu |
| PHILCO | PCS2952 | Dull, bright when turned off | Screen voltage was very low even when measuring directly on the wire, with it disconnected from the board | Changing the tube socket, which, if it leaked, killed the focus voltage and the screen on the fly | jasvan souza |
| PHILCO | PC1442 | White tla with retrace | Zd 304 | Replacement | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | TV PH21E | Does not turn on, LED flashes, +b with 20v | Changed power supply | R839(82k) replaced to 100k | CABESSÃO NATAL |
| PHILCO | PCM1444 | Turns off after some time | C719 capacitor replacement | LOU | |
| PHILCO | PH21B | Turning off in seconds | High power supply, 180v. rgb with 230v. | R552 from 100k was replaced to 120k, just replace it!!! | gmcmaster10 |
| PHILCO | PCS2976S | Inoperative, it exploded, according to the customer | Fusel, q901 party, d902/903/908 and ci 901 | Krul | |
| PHILCO | 1444/2044 | The LED just blinks, it doesn't turn on, tsound is only 16v in the 20v power supply | C708 22n with leak | Just replace the capacitor | Paulo Sertel Itararé SP |
| PHILCO | 1444/2044 | Horizontal fallen | C 709 and c707 with leak | Just replace the capacitors) | Paulo Sertel Itararé SP |
| PHILCO | TPF2130 | Does not turn on LED off | C906 open | C906 replace | ELETRONICA MAURI JUNIOR |