Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4741
Results: 4741
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | TP-1452N | TV does not work when turned off and making noises at the power supply | Capacitor,position,c913=1mf/50v | I replaced it and plz | ELETRONICA MEDEIROS |
| PHILCO | PCM 1444,1446,2044,2046 | Works normally with screen and LED blinking like a solution | R713 100k open | I replaced it and resolved | antonio dos santos lima |
| PHILCO | PCM-1444 -1446 -2044-2046 | Running away from color, sometimes you want to scroll vertically but it's not enough to scroll the image half tremola | C205 | I replaced c205, 208, 702 solved | antonio dos santos lima |
| PHILCO | TPF29S4F | It doesn't turn on, it just stays on stdby, sometimes it sets up the power supply and sometimes it doesn't work, it seems like a bad contact but it isn't. | 3.3v low supply | Substituir q903(bc337-25) e zd902(zener 4,7v) | NARDINHO |
| PHILCO | PCS2952 CPH06 | Activating the protection and then turning it off and with +b180v with 260v | Causes depleted width capacitor c711 and c712 | klein | |
| PHILCO | PCM-2046 | Blue screen, no sound but normal osd. | C-722 470x16 | FERNANDO S | |
| PHILCO | PCM-1444 | Running away acor, or a hundred color pb, | Zd504 5v1. can you put the dz4v7 it works ok | GLUJ SAT Eletrônicos | |
| PHILCO | TP-1454 | Tv inoperative | Transistor fet switch shorted conducting and killing fuse | Replace of the same | jayjunior |
| PHILCO | PCM 2046 | Out of sync | 2.2uf/50v electrolytic capacitors near the ci one chip. | Replace of the same | jayjunior |
| PHILCO | PC-1444/2044 | No synchronization turning on. after a few minutes the image becomes normal. | C-205, c-409 of 2.2x50 and c-722 of 1x50 (electrolytics) | FERNANDO S | |
| PHILCO | PC-1444/2044 | Severe noise in the sound, normal image | C-722 = 470x25 | FERNANDO S | |
| PHILCO | TP1454 | Faulty vertical...horizontal output getting very hot | Change the circuit ic601 tda9309.... place a 12r resistor between the base and emitter of the horizontal output transistor | FUBULHA-PI | |
| PHILCO | PCM1444 CPH05 | Does not open the vertical, good ci, tsound is no 2.8 volts on pin 43 of the ic-501 | Check if the r-802 12k resistor is open | If said resistor is open, replace it. | Paulo Sertel Itararé SP |
| PHILCO | PCM1443 CPH05 | Horizontal K (again) | C-709 10nx100v open (no capacity) | Replace it with a new one and a hug | Paulo Sertel Itararé SP |
| PHILCO | PCM2043 CPH05 | Tsound is sound, tsound is an image but the LED blinks and tsound is no voltage on the protector | The r-713 resistor changed (interrupted) | Substituir o r-713 100k | Paulo Sertel Itararé SP |
| PHILCO | PCM2043 CPH05 | LED flashes (standby) and seconds after switching on | C-722 470x16 volts alterado | Replace it with a new one, if resolved | Paulo Sertel Itararé SP |
| PHILCO | PCM2144 CPH05 | Tremulous image | C-205 2.2x50 volts exhausted | Replace the c-205 with a new one and readjust the trimpot p-201 10k | Paulo Sertel Itararé SP |
| PHILCO | TP14U56 | Without image, with osd and sound | D602 | Replace d602 with leak | joaomvjr |
| PHILCO | TP20U56 | Without image, with osd and sound | D602 | Replace d602 with leak | joaomvjr |
| PHILCO | PH29C | Blinking LED doesn't work | D 810 fr154 | macceletronica |