Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4741
Results: 4741
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | TFP2940 | Turns on, protects and the LED blinks | Replace c 1701 and c1703 5n6?1k6 and adjust screen | Antonio Martis | |
| PHILCO | TP2000 | C715 swap | This email address is being protected from spambots. You need JavaScript enabled to view it. | ||
| PHILCO | TP2054 | Normal power supplys, when turned on it works for + or - 5 seconds, and goes into protection, (the panel LED keeps flashing) | C718 swap | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| PHILCO | TP 1454 | Vertical bar on the left side of the screen approximately 3cm | Change capacitor smd c 705 2n2 pin 16 of the micro does not measure can be replaced with a common ceramic | Replace c705 2n2 | fabiusmax |
| TV PHILCO | TPF2121 | Only on stand by, with noise at the power supply. | Q901 faulty and d908 shorted. | edsomvideo | |
| PHILCO | TP1452N | Fountain sobbing | C911 e c913 | Replace both if it continues, replace ic 901 | Elias2305 |
| PHILCO | TP1452N | With colorful stripes across the screen | R708 (I replaced the vertical output, micro, tda) and it was just low voltage.... | Replace without testing.. | Elias2305 |
| PHILCO | TP29C21 | Charging power supply capacitor, power supply does not oscillate | D915 from primary power supply | This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI | |
| TV PHILCO | PCS2956 | Tv philco pcs2956 that the image is normal, but tsound is a strong noise in the sound of the channels as if it had an unadjusted aft coil. | I replaced the ic501 tda8843 2y then it was amazing. | bf.colatino | |
| PHILCO | 2049 | When turning on, only the channel number (OSD) appears, increasing the screen the image appears, but the next day it is the same thing | Resolder all smd resistors on the tube board. | HP ELETRONICA | |
| PHILCO | PC2048 CPH06 | Sometimes the TV doesn't turn on, it keeps banging and clicking on the speaker | Intermittent 9v power supply.. check all power supply and pay attention to the 9v inductor that presents this intermittent defect. | Replace blue inductor at 9v output | ELETRONICA ROBSON (DEBIQUE) |
| PHILCO | TP 2920 | When turned on, it arms and returns to stand by, heating the filament, you can see who has video feed | Replace c1701 6k8 and c1703 | itan (cabeça) | |
| PHILCO | TP2921 | Turns on but after a while it turns off and remains on standby. I turn it on again after about 6 minutes it turns off | Change the c805 it comes from 22uf\160 change it to 47uf\160v also change q830 (replace everything without measuring ok) | Replace the c805 it comes from 22μF\160 replace it to 47μF\160v also replace q830 (replace everything without measuring ok) | Deusomar |
| PHILCO | TVPH21B | Dark image when the TV or DVD signal comes in. Note: when tsound is no signal, the brightness remains normal. | Diode in4148 (vd 461) shorted on the abl line | marcelo de castro | |
| TV PHILCO | PC-1445 | +b 95 volts does not turn on the TV, only with a humming sound at the power supply. | Resolved by changing c911 220uf x 160volts. | BF.COLATINO | |
| PHILCO | PCS 2700 | TV doesn't turn on but it makes a low hiss at the power supply +b it was 15v | I replaced c911de 22omf x 160v | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| TV PHILCO | PC2028U | I got this TV with the following defect: when I pressed the power button, the TV made a buzzing noise and wouldn't turn on. | I found r 736 (120 r) open - pin 6 of the flyback - I changed the resistor and flyback (fb 3412/13), and the TV worked. | bf.colatino | |
| PHILCO | PT 1453 | I'm sound | R- 409 | Perse | |
| TV PHILCO | TP-2920 | When I turn it on it turns off then no sound no image goes into protection | Capacitor 6n8/j/1k6 defective. | Resolved | BF.COLATINO |
| TV PHILCO | PCM2051 | Tv semp 2084fav nao sai de standbay. | This TV triggers the power supply but it doesn't have high voltage, I found 9v on pin 31 and pin 32 1.8v on q402 c=40v b=0.3 and c=40v and +b is normal. I removed the vertical output off the board and released it. audio output, without success, does not turn on, before this defect occurred, the flayback was changed and it was in operation for about 3 hours and the image was erased, leaving the audio going back and forth. | I decided to replace the horizontal output q404, and testing it up to the x1k scale, it showed if it was good, to my surprise at x10k it showed if it was running away, it was just for another and everything was fine. | BF.COLATINO |