Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4758
Results: 4758
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| TV PHILCO | 29S4F | If I turn off the vertical output of this one, it turns on, if I turn on the output it keeps giving the defect mentioned above, tripping. I already changed the vertical outlet and it didn't help. | The problem was in the deflector socket, I removed it and cleaned it, as it was oxidized, I resoldered it and the problem was resolved. | BF.COLATNO | |
| TV PHILCO | TP 2054 | This TV has 3 colored lines at the bottom, what doesn't match is the output on pin 21 of the computer which is at 0.2 v, pin 22 ok is at 0.6 v o + 12 and - 12 v ok. | The c. i. vertical and the voltage at pin 21 of the computer, which was 0.2 v, became 0.5 v, so I just changed the vertical output and the TV returned to normal. | BF.COLATNO | |
| TV PHILCO | TPF 2902 | The volume of the TV, it increases every 4 | I removed the power cable, simultaneously pressed channel + and - for 20 seconds and it was normal. , | BF.COLATNO | |
| TV PHILCO | PCM205 | This Philco PCM2051 TV received no image. on the fly back, pin 6 should have 45v and has zero and on pin 5 it should have 180v and has 80v. When he was admitted, the varicap was broken inside (coils). I replaced the varicap and the transistor q201 and c206 to repair the channel programming, which was not working. It turns on normally, gets a blurry image and if you move the screen, tsound is a recoil. | I managed to resolve the defect. I replaced the fly back due to lack of internal insulation. I also managed to change the varicap at the dealer and resolved the high voltage on pin 7 of the varicap, it was defective. | BF.COLATNO | |
| PHILCO | * CPH05 | Horizontal bars | C 702 of 1uf with altered ers | By exchanging the capacitor for another of the same value, the defect was remedied. | edrod |
| PHILCO | TP2920 | It turns on then goes into protection, the LED starts flashing.c | C1703 and c1701. | This email address is being protected from spambots. You need JavaScript enabled to view it. | |
| PHILCO | TP1452N | Doesn't start | Defective power supply ci | Tda4605-3 power supply IC replace | johnny busnadiego |
| TV PHILCO | 1454 | Then leave and don't care | R910 and r912 open, check diode minus 12 volts was shorted | BF.COLATINO | |
| TV PHILCO | 20V56 | Drizzle.no channels work | I had 33v and the necessary voltages, but when I checked the date and clock line with the scop (oscilloscope) I saw that tsound was no clock signal. | R202 100r smd version was open. | BF.COLATINO |
| TV PHILCO | PC 1446 | Works normally but keeps flipping channels | Just wash the processor with theener and the processor is back to normal. | BF.COLATINO | |
| PHILCO | TP2052 | +b pressing led off | Capacitor as low capacitance | Replace the 1 μF capacitor c 913 that is in the primary power supply TV ok. good luck | george pontes |
| PHILCO | PH 21C | Closing vertically at the top and bottom | C401- 882j 100 | Barter it | This email address is being protected from spambots. You need JavaScript enabled to view it., jaicós PI |
| PHILCO | TPF29S4F | TV arrived at the inoperative workshop. I found a diode on the yoke board with a short in position d1701, I replaced it with a new one, the TV started working again, but the screen had stretched corners, I tested the entire yoke board but everything was ok, I went into the service menu and more. it was a defect; Luckily, another TC Philco model TP2920 arrived which had the same chassis, so I ordered the yoke plate and put it in, it was still defective; So, look at the other board, tsound were two wires coming from the 706 capacitor position going out to the yoke board, so I did it from the other board; negative position of the capacitor n pin 2 of the cm 1307 positive n pin 1, then also change the resistor n position r 1702 to 47k then just joy ;8817 | Missing wire that connects the yoke with the position d c 706 | Remove capacitor c706 put two wires in its place connect socket cm 1703 which is n yoke + a 47k resistor | marcos melo cascavel ceara |
| PHILCO | TVPH21SS | Doesn't start, doesn't have +b. | R520 of 120k open at power supply. | It was just a matter of changing it and it was ok. | FRANCISCO - ELETRONICA SÃO FRANCISCO This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | TP2920 | Turns on then goes into protection, LED flashes. | Replace c1701 and c1703 | ||
| PHILCO | PC2041 | Turning off after flyback replacement | Resistor r723 (27k) open abl line | ARAUJO | |
| PHILCO | TP2052 | It doesn't turn on, or it oscillates and turns off and the LED keeps flashing | C706 6n8 leaking capacitor | I put another one it worked perfectly | FRANCISCO RS |
| PHILCO | TP2053N | Blinking LED doesn't turn on | Shorted deflector coil | Replace the coil | francisco rs |
| PHILCO | PC2013U CPH02 | Vertical closed | Capacitotor c 611 de 100uf/100v rim | Also replace c607 at 10μF/63v and c609 at 4.7μF/63v | francisco rs |
| PHILCO | PCM2146 | Inoperative, stand-by LED flashes and does not turn on | Capacitor c905, replace as it is open | claudio e reinaldo |