Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4741
Results: 4741
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PCM2044 | Led screen with retrace line without/picture with/sound | Kinescope plate socket | Tsound is no point in testing, you have to replace | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | PCM2051 | Dark screen with no sound and it kept making intermittent clicks | Cap 471n which is close to the horizontal outlet | In my case I resoldered the board and replaced the capacitor | serginhosond |
| PHILCO | TPF 2140 | Normal power supply, but when you turn on the by, it then turns off, that is, it does not start. | High voltage at + 180 that powers the rgb circuit. Turning off the resistor - r 725 that polarizes the PC's protection (3.3v), the TV works, but it came with a reduced frame. the voltage was 180v - it was 215v. causes the c715 of 6n8 1k6, changed to minus. | Replace the c 715 (6n8 1k6v) and run for the hug!!! | Luna |
| PHILCO | TV2054 | Out of tune | Tuner | Replace the tuner | eletronicaapolo |
| PHILCO | PCM1444 | Vertical semi open | It has lines and a mirror image at the top of the screen | Changing the vertical output ci tda3653b or 3653bq solves the problem | ffeet |
| PHILCO | TPF 29S4F | After a lightning strike, the TV stopped on the +b line so it only has 12v instead of 122v | Ic 101 defective microprocessor | FLAVIO | |
| PHILCO | TP1452N | Fountain with flashing led | C 1 uf 100v shorted | Replace for a new one!!! | EVALDO GOMES ELETRÔNICA GOMES URUÇUI-PI |
| TV PHILCO | PCM 1444 EMOTION | No image | Varicap | Check 5v and 32v if ok replace the varicap | wagner |
| PHILCO | 1446 | Cuts the image and weaves it in half the screen | Changing the 10x350 volt capacitor on the 170 volt line that goes to the tube plate | HP ELETRONICA | |
| PHILCO | PC2138 | In the UHF frequency signal, you tune the TV and memorize the channels, it's fine, but if you turn the TV off and on again, the tuning is off again. | Q101=bc550 and c110=100pf, tsound is no point in testing, both are good in the test. | Replace without testing and it will look great. | Armando da Eletrônica só Tv. |
| PHILCO | TPW-3280 | Screen takes a while to light up and then keeps opening and closing horizontally | Capacitor c708 de 5n6 x 1600v. | Persio(TVCompany) | |
| PHILCO | PCM 2046 CPH-05M | No contrast | R716 100k | Senna | |
| PHILCO | TP20V56 | Little shine | Zd701 shorted near flyback | Replace and ready zenner 8v2 but can be replaced by a 6v2 | fabiusmax |
| PHILCO | PCS2976 S | TV inoperative, primary power supply fuse blowing | I've already gotten used to these philco TVs because almost all the models I've gotten with a blown fuse, I'm already going to the c909 which is next to a heatsink of the mosfetic901, it shorts out and it's already a power supply as a precaution if you don't If you have the schematic of this TV in your hands and only use a 4n7 tick style capacitor for 500v, thanks guys, a hug to everyone and see you next time, if you have any questions about this TV, just call me or add me on MSN, | Replace o c909 4n7x500v | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | PCS-2976 | TV starts, but the filament doesn't light up, it goes out and the LED keeps blinking. | Capacitors 715 and 730 with severe capacity loss. Just to give you an idea, the 8n2 capacitor 715 had less than half its capacity, the 4n7 c730 had its capacity reduced to 3n9. Replace these capacitors with their correct values and the device works normally again. | jfr | |
| PHILCO | PCS-2976 | Dark stripe on the left side | R 712 10k changed | ELETERONICA ROBSON(DEBIQUE) | |
| TV PHILCO | PCM 1444 | The TV had a blinking LED, worked normally and had stripes on the left/right sides. | R-719 open | Replacement | wagner |
| PHILCO | PCM 2046 CPH-05M | LED flashing and when I opened the flyback screen the vertical appears closed with the line reduced, as if it were a flaybk power supply | Ic 701 is what powers the hvcc of the 8361 and vcc of the vertical pin 10 | I replaced it and it worked normally. good luck to everyone | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | TP14U56 | Does not oscillate (turns on). normal voltages. it is only on standby. When you press power it makes tick tick tick and stays on stand by. | I released pin 3 of the photo coupler and then the TV oscillated (turned on), then turned off. I noticed that the vertical core overheated in 3 seconds. so I killed the charade. la78040n. | Tec vídeo | |
| PHILCO | TP 1410 | The TV tries to turn on, the LED goes off, disarms the demagnetizer relay, then the LED starts blinking, it doesn't work. | Resolve or replace r 931 | caio |