Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | TPF2121 | Doesn't work via remote | Change without measuring sensor and c1102, c1103 | Sensor take on toshiba u17 board and the same | ELETRONICA MAURI JUNIOR |
| PHILCO | PCM2046 | No characters | Zd601 | apolo t.c. | |
| PHILCO | PCM2046 | No characters | Zd601 or some in-line component | apolo | |
| PHILCO | PH200 | It stays locked and the display shows the name disc | L6 position smd coil | Just replace and run for the hug!!! | Eletrônica Áudio e Vídeo |
| PHILCO | TP 2920 | TV sometimes wouldn't turn on and there were thin, colored scratches on the top of the TV | Capacitor poliester c1703 (6n8) | marciorvgo | |
| PHILCO HITACHI | PC2004 CPH-02 | Vertical closed 5cm at the top and 2cm at the bottom. without changing the linearity or height. | Vertical output transistor with changed hook. the base, emitter and collector junctions being perfect, one with gain 84 and the other 36, measuring a good one gave 33. | Replace q601 e q 602. | Ademir tc |
| PHILCO | PCS 2952N CP01LR01 | TV inoperative, burning horizontal output. | When disconnecting pin 1 of the fly back (h out) the voltage of 120 volts appeared | Burnt horizontal output bu2508dx, open 10r resistor 2914 and 707 diode (with very high leakage), I replaced them and the TV worked. | jorgebetto |
| PHILCO | TP2052N | Normal league dark screen | Lights up filament has high voltage dark screen | Replace tube socket and adjust the screen | toninho da eletronica |
| PHILCO | TP2053 PC-02R0 | Dark image +12v giving 9v, +12v vertical ic601 and ic905 7809 | I replaced c914, it wasn't d908 | Replace d908 for another | ELETRONICA AGUIAR |
| PHILCO | TPC2910 | Intermittently turns on or off and makes noise on the fly-back | Resolder the fly-back and replace q830 bc337 | ||
| PHILCO | PH21M SS | Does not turn on when heating r816 see also transisto q802 | 3v3 pin of ci tda1114ps/ne/3 shorted or leaked | Replace it and resolve | MARCONDES LIMA,Jaicós-PI- Brasil |
| PHILCO | TP2054 | Turns on, after a few seconds it turns off and the LED starts flashing | D909 shorted, r910 and r912 open | Replace them and run for the hug | Eletrônica Staub |
| PHILCO | PH 21C | Menu stuck | When asked for the password, type 4711 | paulorusso | |
| PHILCO | TP1452N | Nor +b | Short c921 (1nf) | Luir | |
| PHILCO | TP 29C21 | TV works without sound, no image, dark screen and indicates no signal | Replace varicap | Roque | |
| PHILCO | TV PH21SS | Vertical closed the bottom | Vd 564 power supply | Just fix it and good luck!! | Jhone eletronica |
| PHILCO | TP1454 | Does not turn on, stand by LED flashes quickly, secondary voltages are low | In my case, the diode was missing in the primary power supply d916 smd, connected to the zeners zd906 and 907 | Replace or replace | eletronica fernandes (to) |
| PHILCO | PH29 US | Vertical closed from the middle to the top bottom apparently normal | Vd 401 (1n4004) after changing it I noticed return lines at the top of the image it was the c406 (100ufx25v) | Replace both without thinking too much for 1n4007 which has the higher voltage and the electrolytic for a 100μFx50v | rolf |
| PHILCO | PFL2922 | I changed the memory and there was no sound | Go into setup and adjust the model function, in my case I put 29 and it worked | But it only took 01 av, I don't have the manual to see which model is correct. | This email address is being protected from spambots. You need JavaScript enabled to view it. |
| PHILCO | PH21A PH14B | Doesn't start | Check voltage of 3.3v on pins 54,56 and 61 of ci n301 (om8370) | If there is no 3.3v voltage, check the 10μH inductors (l752, l753 and l754) | Andrade Sequeira |