Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
PHILCO | PH21MSS | Turns on and off quickly, it doesn't even take time for the image to appear, | Change without measuring c828 and c833, 1000x25v both. | DJ PITUKA | |
PHILCO | PCX11000 | Speaker does not turn on. good power supply. | Check d3 smd diode on main board. is below the glue. It's an ss24. If you are testing the power supply board outside the box, consider the 33v oscillation to be normal. | Sperotto | |
PHILCO | PH21M SS TURBO | Burning vertically | C 307 100uf / 63v exhausted | Replace | Eletrônica Mauro Mascarenha - Parazinho Ceara - Tel : (88)981422821 |
PHILCO | PTV39N92DSGWA | TV doesn't turn on, LED blinks slowly | Capacitor cw922 shorted | Substituir | Matões Assistência Técnica |
PHILCO | PH14 ULTRA SLIM | Replace | Vd 851 of hz5c2 can put the diode in4148 | Replace | Eletrônica Mauro Mascarenha - Parazinho Ceara - Tel : (88)981422821 |
PHILCO | PTV-28G50SN | TV turns on without picture | Shorted smd diode and stuck smd fuse on board v.com | In my case it was just the two defective components, I replaced them and the problem was resolved. | jose fernandes dos passos |
PHILCO | PH32M3 | Turns on, everything is normal, after a few minutes, video disappears, back light is on, keyboard doesn't work. | Capacitors ca08, ca10, ca 15. | Replace of the aforementioned capacitors. | arock |
PHILCO | PH32E32DG LED | Totally off | 24v power supply rectifier diode, position d1d0 | Substituir | Matões Assistência Técnica |
PHILCO | PH19B16DM | Turn on the TV and the screen keeps changing color without any characters | With the power supply in place, I grounded a wire and passed it to the CI u201 pins and then I assembled the TV and it went back to normal. | fabiusmax | |
PHILCO | PH32E20DSGWA | Leds writer | Changing three 100/50 and one 470/25 capacitors in the power supply secondary. | Danubio | |
PHILCO | PH21B PH08K-A (VER:0.7) | Vertical almost completely closed, open only about three centimeters halfway up | Defect a 39k precision resistor changed to more or less 70k in position r 320 close to the micro | Jr eletrônica | |
PHILCO | PTV32D12D | Mute, without sound | Ca23 close to the sound output. | Replace | Marcondes Ohm Eletrônica Jaicós PI |
PHILCO | PH21M SS | Does not turn on with a small buzzing sound and heating up a lot r402 | D815 open rectifier | Marcondes Ohm Eletrônica Jaicós PI | |
PHILCO | PTV32D12D | Audio only. | LED bars with open LED. | I removed the rb840 inverter resistor (4r7) in a previous repair. but returned in 2 weeks with problems with the LED bars. I replaced the rb837 resistor (3r) with a 3r3 one. The measurements were 61.7v and 248ma, it was 58.7v and 168ma. I hope tsound is no return. | Eletrônica R-Tec |
PHILCO | PH14D CCP-3400 | TV stopped does not turn on stand by | R822 470k changed to 670k | In this case it was resolved | Wellington TV |
PHILCO | PH21 US A1 | R407 pifado | Charred | Replace the 1k r407 this resistor has a plate that comes with the number r407 or r460 the value is the same 1k | Sinailson furtado |
PHILCO | PH29B | Tsound is an image but no sound, the sound is only available in AV mode and not available in TV mode. | I changed the capacitors upholstery c833 and the others near it resistors diodes but it stayed the same way I saw the voltages were giving 12 volts arriving at the ci 7266 amplifier I put sound signals to see if the ci was amplifying pins 4 and 12 and it was yes I put them in the micro was also yes, until the amplifier I changed the micro processor and nothing | My solution that solved it was the epron ic 202 that solved it | Parente maia |
PHILCO | PH58E38DSG | Turns it on, writes philco and between 12 and 15 seconds the TV turns off the philco and has a dark screen, but the LEDs are on and it turns off completely and goes into stand-by. If you press power it accepts and does it all over again. | As the manufacturer informs, this symptom is related to the LEDs, but to my surprise I risked updating it, which I downloaded from the website itself and the TV was perfect. detail that if it was an LED, when disconnecting pin 4 (fail) of the cable that goes into the LED drive board, the TV was supposed to work if it was a defective LED and actually the TV, even with the fail turned off, did the same, it turned off afterwards 15 seconds....so that's why I risked the update | Update software. | MIGUELTV |
PHILCO | PH32M DTV | Turns on and off (backlight defect) | R-0 of the inverter board | Resolder or replacement | Maike sorriso-MT |
PHILCO | PH32M DTV | TV turns on without characters. | Poor contact on jumper cn17, not allowing voltage to reach the screen connector | Remove jumper and replace | Reinaldo |