Philco TV Repair: Common Faults and Solutions.
Search: Philco
Results: 4740
Results: 4740
Philco Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| PHILCO | PH21M2 | Works more hissing at the power supply | Change the ncp 1337p power supply oscillator | Dominguinhos | |
| PHILCO | PH39E53SG | Adaptation of philco ph39e53sg board to sti le4065(b)f. | Image was inverted (upside down). to solve: use philco control (obviously). enter service mode and make the following settings: menu>image>image mode>user, position the cursor in "contrast" and type 9705>project id>change from 5 to 6>ok. | Credit to the youtube channel: sharing ideas and knowledge " https://www.youtube.com/watch?v=xpl0ctbkdiw " | Eletrônica R-Tec |
| PHILCO | TP14U56 | Flyback with crack and leak | Changing the flyback jf0501-19192a if you don't have it you can use the fsv-20b013 in this case you must cut the track on pin 5 and jump from pin 3 to r714. | samuel leite | |
| PHILCO | TP14U56 | Flyback with crack and leak | Changing the flyback jf0501-19192a if you don't have it you can use the fsv-20b013 in this case you must cut the track on pin 5 and jump from pin 3 to r714. | samuel leite | |
| PHILCO | PH32B51DSGWA | Intermittently turns on and off. | 2 transistors varying voltages the vw901 and vw917 check the capacitors cw926 and cw930 if the voltage is varying | Replace transistors vw901 and vw917 I don't have the schematic, I took it from a similar damaged board. | Antoni Garcez |
| PHILCO | PH24M LCDDTV | TV turns on only through the control without audio, audio comes on after some time | C,1500mf/35v 2x and c1000mf/16v 2x next to the power supply board connector for the main board | It seemed to be a symptom of the main board, but after replacing the aforementioned components, everything returned to normal. | PAULO |
| PHILCO | PH21B | Image with a lot of drizzle | R317 from 4k7 open | Replacement | Eliel Magno |
| PHILCO | PH39E37DSG | Does not turn on - 12v and 24v supply low and pulsing | Resistor smd rp25 - 33k avariado | JOÃO LUIZ | |
| PHILCO | TV PH 14E | Does not help | Fly-back | Replace o fly-back bsc25-0232q | Sinailson furtado |
| PHILCO | PH14 ULTRA SLIM | I'm sound | Resistor 603 | Replace the same | Edval |
| PHILCO | PH40R86 | Even in standby, the LEDs stay on, with very low brightness, but lit | It is visible that in the secondary tsound are two 47/100v capacitors | Replace capacitors... | MIGUELTV |
| PHILCO | PH21SS | The television turned on with a noise at the power supply and vertically deflected only halfway up, it overheated | Capacitor c562 with short lead was not making contact with the board even though it appeared to be soldered. | Replace and resolder (edfesom varjota-ce) | Edfesom |
| PHILCO | PH24B LCD | Takes time to call. and when it turns on, it comes with multiple images, or duplicates (as they say). | Power supply with bad electrolytic capacitors. change all the stews. enter service mode and change the config id to cmo-m236h1 (service mode: menu>contrast>9735). (center sound tip (thanks)). | Eletrônica R-Tec | |
| PHILCO | PH39E53SG | The Philco logo appears and then goes out, but you can see that the white light is still on. | Apparently a defect on the main board. | I removed the memory and re-recorded, the TV worked normally again | Jhonnes Palmares |
| PHILCO | PB329BT | Turns on but no audio | Transistor q08 open | Replace 08 you can put bc847 | jorge-ivoti |
| PHILCO | PH21MG SS | Turns on with noise in the transformer and burning r804 from the primary power supply | The cause of the defect was the capacitor c803, the famous biteludo | Replace of the same | ASSISTEC |
| PHILCO | PTV55U21DSWNT 4K V.A | Dark screen, no image, LED bar ok | Problem on the t-com, when disconnecting the right flat from the lvds the right side image appears. | Isolate tracks from this flat (cn 1003 connector) 9,10,11,12,13 and replace the npn c5886a transistor, also check the a2097, on the t-con | Alancocteau |
| PHILCO | PH40U16DSG | Inoperative without standby | Measuring power supply only had voltage on the rectifier bridge | Componentes danificados up 101 ncp 1251 (pwr) qp 201 7n65 coloquei 10n65 (10a ) dp 203 1n4148 zdp 201 zener 22v rp 212 22r rp 208 0,22r 3w rp 213 1k5 rp 219 100k 2w | srsabia |
| PHILCO | PH21MSS | Image shaking shaking with changed power supply 139v | R810 15k (main power supply) | Tião Serra | |
| PHILCO | PTV40E21DSWN | Front LED flashes quickly and the TV does not turn on | Solution to change 3.3v u2p2 regulator on the main board, it only had 2 7v | Eletrônica Valdecir |