SAMSUNG TV Repair: Common Faults and Solutions.
Search: SAMSUNG
Results: 3754
Results: 3754
SAMSUNG Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SAMSUNG | UE46F5000AW | Does not light up, restarting and never turning on | See cold welding in the power supply choper | Edson SP | |
SAMSUNG | SYNCMASTER 540N | Turns on but no image appears, just standby light on | Shorted smd capacitor c614 | Changing the capacitor, remove it from the board and turn it on, if the image appears, replace it with another equivalent. | MaskarenzzO |
SAMSUNG CURVADA | UN49K6500AG | Burnt out LED bus. | High LED current with 91.2v and 500ma | Replace the LED bar (side) and replace the resistor (r9873) from 0.56r to 1r, the current drops to 88.2v and 220ma. Note: this model tends to burn out the LED bus and also the diffuser acrylic. | Evando Viana |
SAMSUNG | LE40R86WD | When it heats up the image goes out. Sometimes it turns off, locks or freezes the screen. | Defective power supply capacitors, especially the electrolytic ones inside the oscillator ci cage | Edson SP | |
SAMSUNG | UE32C5700QSXZG | TV only turns on after several attempts and insisting on the control button | Power supply ok. ic203(z1031ai) with excessive heating | Cardozo | |
SAMSUNG | UE46ES8000 | Frozen images appear, with mixed colors, the TV turns off, it appears to be the LCD panel | Oxidized power connectors | Cardozo | |
SAMSUNG | UN50NU7100G | Backlight keeps turning on and off, no image | I isolated some tracks from the lower lvds cable on the main board. got the perfect image. good luck to everyone! | Eletrônica Cecé. Brumadinho MG | |
SAMSUNG | LE40R74BDX | Does not have backlight | All voltages are good except those in the final stage of the inverter, ic804 (fan7382) defective. | Replace ic804 | |
SAMSUNG | UN50RU7100 | LED current reduction | Alter resistor r9101 for 4.7r | reginaldo moronte,eletronica junior caldas novas | |
SAMSUNG | UE55KU6100 | Does not work, does not turn on standby LED | Voltage of 13v with +/- 9v. Defective solders on capacitors c245, c247, c248 and c280 | Re-weld the affected lines | |
SAMSUNG | UE55H6200AW | Turns on, backlight comes on but tsound is no image. | Fault in the LCD panel, tsound is a short or leak in the panel capacitors. | Check all capacitors connected to the power supply line, especially the 22µf capacitor at the end of the line | ERP-ASSIST |
SAMSUNG | UE32J5200 | Image with poor colors without the possibility of adjustment | R5_gain in incorrect service menu with no possibility of correction | Rewrite memory 24c256 | ERP-ASSIST |
SAMSUNG | LT24B301EW | Stand-by light flashing, does not start | At power supply, 1200µf/10v capacitor disabled | ERP-ASSIST | |
SAMSUNG | LE22C450E1 | Doesn't start. led blinking | Capacitor shorted to the rf input | Pablo | |
SAMSUNG | S27F358FWU | No backlight | Check replace 60v 300ma sot-23 2n70002k | ||
SAMSUNG | UE46F6320AW | Turns on and off, power supply goes into protection | By deactivating the protection (r bridge qs861), the power supply starts and does not turn off. LED strip failure | Pablo | |
SAMSUNG | LN32D450 | Does not work, stand by LED on activates power key, LED blinks but does not turn on. | Check voltage on ic205, 1.5v. absent. check possible short in c 1020, 1115, 1141 | In my case, c1141 shorted. replace and go for the hug. | arock |
SAMSUNG | 632NW PLUS | Doesn't start. Sometimes the LED doesn't light up or it lights up dimly. if turned off for a few days, it works again for a while. | 5.1v and 14v line with varying voltage | Replace the 5.1v (c109/c110 1000μF) and 14v (c113/301 820μF) line capacitors. all four were looking good and measuring ok. I just replaced it and it resolved it. | PIXEL ASSIST |
SAMSUNG | UN48JU6020G | Power supply secondary completely dead/turning off after a while. | Cold solder on the main transformer of the power supply / if pin 1 of the icm801 has less than 170v, the polyester capacitor cm847 will be leaking. | Carlos Araújo 82 9 93677063 | |
SAMSUNG | UN50TU8000G | Burning the LEDs | Backlight with voltage above normal. | Solution: remove r901 from 2.4Ω. and don't worry, it won't burn the LEDs again. | Eletrônica Evolução |