SEMP TV Repair: Common Faults and Solutions.
Search: SEMP
Results: 2828
Results: 2828
SEMP Repair Guide: Common Issues and Fixes
| Brand | Model | Fault | Detailed Problem | Solution | By |
|---|---|---|---|---|---|
| SEMP TOSHIBA | TVC160 | Vertical partially closed | Verficar q803 (2sb546) | Sequeira | |
| SEMP TOSHIBA | TVC160 | Power supply takes time to start | Verificar c811 (10/100v) | Sequeira | |
| SEMP TOSHIBA | TV2490 U14 | Power supply with oscillations | Verficar R876 (220R) | Sequeira | |
| SEMP TOSHIBA | TV2090 U13 | Scratches at the top of the screen | Change c308 | Sequeira | |
| SEMP | TV2083FAV U11 | No menu, no volume bar (osd (on screen display) missing) | Rb20 open | Locate the smd resistor rb20 which is at the base of the qb20 and pin 7 of the vertical output. | Helio Eletrosonic |
| SEMP | TV1451 OAV U19 | Does not turn on, without power supply and comulating current | Open 220k r860 and changed 5.6v d876 | Replace | EletroClaudio Aguas Belas |
| SEMP | TV2015MM U17 | Only on standby | I removed the cap. c417 the TV worked normally | note: inserted by ilis drop electronica, I want to say that you were wrong! If you remove cap 417, the high voltage goes into excess and burns the horizontal output, throwing high voltage into the tube and burning it, I mean, we have to be careful with tips, thank you | eletronica do pingo |
| SEMP | TV2090 U11 | Scratched shutter-type screen and missing height. | Ci vertical output defective. | Replace tda8403k | ÁdrianChapadãodoCéu |
| SEMP | TVC-166 | Normal image just has no characters on the screen and the functions work normally @@@ | I have it from memory ica01=47c434n3528 | Help yourself, leave your tip ass. arni | EETRONICA ARNI-L. LEAL- SC |
| SEMP | TV-1022E/1480E/2080E | No contrast | Ca66 with leak | carlaosbc | |
| SEMP | TV1030 | Vertical closing | Bad contact on the q430 emitter | Scrape the board and solder. | Evandro Estrela |
| SEMP | TV.2016 U18 | Turns on normally after about 10 to 15 minutes it starts to hiss at the power supply and the screen starts closing and turns off | The cause was a ceramic capacitor giving a small leak vlw | C865. its value is 103 | luis carlos |
| SEMP | TV2934SKY SK-91 | Dark screen with no image and no sound, and flickering | Q606 | Replace | EletroClaudio Aguas Belas |
| SEMP | TV2934BL SK11 | Replace | C311 47/200v exhausted | Replace | paulo-maceio/al |
| SEMP | SD-3020VK | DVD completely inoperative (does not turn on) | Dodo 1n4002 (d 18) | The replace of the same | saulo figueiredo |
| SEMP (TOSHIBA) | 2134 | When turning on the screen with excessive brightness | Change cap 4.7/250 voltage 180v rgb | Francisco | |
| SEMP TOSHIBA | TVC 147 | Low power supply with hum. | Dz810 shorted. | Gilcimar Rocha Pereira | |
| SEMP | TV 1484 FAV U11 | When the volume increases, the image becomes shaky, turning horizontally and vertically at low volume, it normalizes. | Change electrolytics near the sound system. | JN ELET.NEVES 100% LEÃO... | |
| SEMP | SD4071U | Does not read any type of media (CD or DVD), or does not spin the disc. | Transistor s8050 which is between the transistors s8550 | After checking: engine, driver, flat and optical unit. replace without testing the only transistor s8050 | Eletrônica Áudio e Vídeo |
| SEMP | SDRX38D | When turning on, it just stays on the home screen and hangs | The 3.3v 0.3a regulator (u18a) on the IDE drive board shorts out. rip it out and place a 1a regulator on the other side of this board (u18, in place of the lime green sticker), eliminate the jumper (0Ω ar2) from the regulator output to ground and place a 100r resistor in its place. This regulator is a little difficult to find, so you can use an old computer CD drive. | Ronie Grein |