TV Repair: Common Faults and Solutions.
Search:
Results: 87427
Results: 87427
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | SLHF600 | Audio flutter/conv. audio/biii | Audio flutter from conventional audio track biii mode only. | ||
SONY | ITA500 | Off hook dial tone intermittent | Will not take the callers call. caller gets a busy signal.do not get a dial tone when receiver is picked up. | ||
SONY | WMF80 | Intermittent radio | Radio does not work. | ||
SONY | STRGX5ES | Power xformer hum after warm-up | Xformer hums after one hour warm-up. | ||
SONY | MPKM8 | Part numbers for release cam and lever assembly | Need part numbers for release cam and release lever assemblyincluding collar, nut, spring and c ring. -hq comments: please refer to service bulletin csv-3 no. 26r. | ||
SONY | SL2700 | Replacement brake solenoid does not work | Servicer stated that the new brake solenoid does not work wheninstalled. -hq comments: the plunger for the brake solenoid (included) must be re-placed also when replacing solenoid because it is different from the oldplunger. | ||
SONY | KV1957R | Intermittent decrease in brightness level, leaky c-307 | Intermittent decrease in brightness level, looked almost likecomplete loss of (y) in formation. at time of trouble - symptom, the vol-tage on pin 4, ic-301 dropped to about 2 vdc. also, voltages at pins 32,33, 34 dropped to .8 vdc. apparently, dc leve | ||
SONY | WMF100II | Grounding of radio connection board | Unit works only when cassette door is opened. shuts down whenclosed. radio connection board has trace worn and exposed causing it toground in the act of opening and closing cassette lid. | ||
SONY | CFSW501 | Battery leaking shortly after installation | Battery is leaking, getting hot and going dead caused by thedc cut-off switch in the ac power plug. this causes dc from the powersupply to go into the batteries. | ||
SONY | VCL0752B | Part number for front and back lens cover | Need part numbers for lens covers (front and back). -hq comments: part numbers are as follows: front = 2-395-025-01please order from kcp. back = 2-395-026-01 | ||
SONY | D55 | Unit dead | After the unit was checked, found were ic503 was burned anddc to dc converter was bad. unit was repaired. after 30 to 45 minutes itstopped playing. i found the same problem as before with ic503 burned andbad dc to dc converter. | ||
SONY | CCDV4 | Green picture | After using the unit on r/p for 30 minutes, picture turnsgreen intermittently on ic-651 dc-dc converter. pin 9 should have 7.7vfound only 4.5v. | ||
SONY | CCDV5 | Part numbers | On page 191 of the service manual item 18 and 2 are reversed.if you order x-3712-170-1, you get x-3712-046-1 part. the ccd-v9 manualshows them correctly. | ||
SONY | XR787R | Tape deck switched directions before tape end | Will not play 120 min. cassette to end of tape. single lengthplay ok. 120 min. cassettes auto reverse within 1/4 of end. found ic701clk. freq. (pin 2) to be 10.451 khz. | ||
SONY | SPP110 | Ics are hard to remove | The ic components are glued down with a red type epoxy. wecannot remove them easily, if at all, in order to service unit. | ||
SONY | CFSW301 | Battery leaking shortly after installation | Battery is leaking, getting hot and going dead caused by thedc cut-off switch in the ac power plug. this causes dc from the powersupply to go into the batteries. | ||
SONY | CDXA20 | Will not start | Will not start. spindle motor will not turn. spacer thatholds motor shaft becomes dislodged from board. | ||
SONY | WMF8 | Motor part number change | Part number 8-835-133-01 is a motor with a control board.this part number now subs to 1-541-414-11 which comes with no controlboard. | ||
SONY | CCDV8AFU | No control panel part number for complete assembly | Reference number 105 does not include buttons - need completeassembly. -hq comments: please order x-368-677-21 for the complete assembly. aservice bulletin will be issued shortly. | ||
SONY | HVM302 | Ic3 on df board is 24 pin, not 28 pin | Hvm-302 service manual shows ic3 with 24 pins, but unit hasic3 with 28 pins. |