TV Repair: Common Faults and Solutions.
Search:
Results: 87417
Results: 87417
Repair Guide: Common Issues and Fixes
Brand | Model | Fault | Detailed Problem | Solution | By |
---|---|---|---|---|---|
SONY | D5 | No focus search function | Unit would not go into focus search mode, thereafter there wasno operation at all. in the process of troubleshooting, i began lookingfor the trouble at ic506 and ic507. there is little in the way oftechnical data relative to waveforms in servicing this | ||
SONY | D5 | Defective search and track jump functions | After pushing play button, unit moves to highest track ondisc. unit then plays that track. if mode is then switched to search,unit continuously searches forward. | ||
SONY | SQD2020 | Noise in r ch | The unit was making clicking noise in r-ch back output evenwhen the master volume control is minimum. | ||
SONY | CDP101 | Clicking popping noise | Clicking and popping noise: replacement of circ decoder solvedproblem. problem was much easier to recognize and confine to a particularblock of the system using test cd #3, particularly track #5 (200hz/tone). | ||
SONY | KV2670R | Set will not shut off with manual, ic-105 memory ic | Unit would not shut off with manual. unit could be turned onby manual. remote would turn on/off the set. we have 4 sets with thisproblem on the west coast area. | ||
SONY | SL2710 | One channel low in hi-fi mode | One channel of audio half of the other channel in hifi mode.looking at pin 7 of ic009 p-p amplitude read 1 volt, on pin 1, read 2vp-p. | ||
SONY | TC78C | New transport cracked | New transport not working. -hq comments: the p/n a-2100-258-a is for tc-78c, not for tc-78cii.there are different parts between the new one and the old one. because ofthis when you repair unit, you have to order each part. there is nowhole tape trans | ||
SONY | BMC220 | Service manual error | Page 5 fig. 1-4 shows incorrect test points for jig hook-up. | ||
SONY | CFS300 | Incorrect pcb marking of transistor leads | B and e leads of q301 are incorrectly marked on bottom ofpcb. diagram of the manual is ok. | ||
SONY | D5 | Defective optical block ass'y (fop) | Unit does not play. clicking noise heard. clicking noisecoming from fop lens hitting disc, fop moving too fast. | ||
SONY | CDP101 | Noise goes into play mode - oscilation at ic601 | 1) poping and clicking noises alternating from l/r ch. addedmodification from t/n 0036 - no change 2) upon power up, unit goes intoplay mode. 3) ic601 #7 12vpp at #1 changed ic601/q608/c611/r614 - nochange. changed optical block as last resort - no c | ||
SONY | WMF8 | Missing part # for a black lever | A tech needed a black lever. this lever limits the switchlever 332, however, there is no description and the part # in the servicemanual. -hq comments: the part number for the unlisted part is 3-319-038-01.we will issue a t/n and s/b soon. | ||
SONY | CFSF11 | Tape transport malfunctions | Head rotation gear is cracked. replacement as per tnla0022/trsb #146 is performed. the transport still jams or hangs up inter-mittently in either forward or reverse play modes. -hq comments: head rotation gear has been updated from plastic to aldie-ca | ||
SONY | TCFX510R | No functions | Various units have come in with functional problems, displayok but no functions. | ||
SONY | KV1946R | Dead, replaced c901 | Unit blows fuse f602 whenever power is applied. found capaci-tor c901 shorted. | ||
SONY | KV1943R | No power on, replace c001 and c003 | The unit would not turn on. | ||
SONY | BMC110 | No p/n for iris motor | No part # for iris motor alone. requires lens disassembly torepair. | ||
SONY | KV20XBR | No color and hue display, replaced ic107 | No color and hue display. | ||
SONY | SL2500 | Ss-10 board change | Old board (ss-10a, p/n a-6715-131-a) uses pcb part number1-605-574-23. new board uses 1-605-574-32. trick and other functions donot work. | ||
SONY | D5 | Play command causes ams to cycle through tracks on disc | Complaint was play command causes ams to cycle through trackson disc till last cut and begin play. preliminary checks showed b+voltages ok. discovered that ff pin 68/ic801 measured 0.6vdc all the timeinstead of 5v. thus mpu was getting ff command all |